ISO 22718-2015 pdf free.Cosmetics 一 Microbiology 一 Detection of Staphylococcus aureus. ISO 22718 gives general guidelines for the detection and identification of the specified microorganism Staphylococcus aureus in cosmetic products. Microorganisms considered as specified in this International Standard might differ from country to country according to national practices or regulations. In order to ensure product quality and safety for consumers, it is advisable to perform an appropriate microbiological risk analysis to determine the types of cosmetic product to which this International Standard is applicable. Products considered to present a low microbiological (see ISO 29621) risk include those with low water activity, hydro-alcoholic products, extreme pH values, etc. The method described in this International Standard is based on the detection of Staphylococcus aureus in a non-selective liquid medium (enrichment broth), followed by isolation on a selective agar medium. Other methods may be appropriate dependent on the level of detection required. NOTE For the detection of Staphylococcus aureus, subcultures can he performed on non-selective culture media followed by suitable identification steps (e.g. using Identification kits). Because of the large variety of cosmetic products within this field of application, this method may not be appropriate for some products in every detail (e.g. certain…

ISO 22007-2-2015 pdf free.Plastics – Determination of thermal conductivity and thermal diffusivity – Part 2: Transient plane heat source (hot disc) method. This part of Iso 22007 specifies a method for the determination of the thermal conductivity and thermal diffusivity, and hence the specific heat capacity per unit volume of plastics. The experimental arrangement can be designed to match different specimen sizes. Measurements can he made in gaseous and vacuum environments aLa range of temperatures and pressures. This method is suitable for testing homogeneous and isotropic materials, as well as anisotropic materials with a uniaxial structure. The homogeneity of the material extends throughout the specimen and no thermal barriers (except those next to the probe) are present within a range defined by the probing depth(s) (see 3 below). The method Is suitable for materials having values of thermal conductivity, A, in the approximate range 0,010 Wm-lK-1 < A < 500 W-m-1K-l, values of thermal diffusivity, a, in the range 5 x 10-H m2s’ <a < 10-4 m2•s-1, and for temperatures, 7’, in the approximate range 50 K < T< 1 000 K. NOTE 1 The specific heat capacity per unit volume, C, can be obtained by dividing the thermal conductivity,…

ISO 15494-2015 pdf free.Plastics piping systems for industrial applications一Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance ( PE- RT), crosslinked polyethylene (PE-X), polypropylene (PP) – Metric series for specifications for components and the system. ISO 15494 specifies the characteristics and requirements for components such as pipes, fittings, and valves made from one of the following materials intended to be used for thermoplastics piping systems in the field of industrial applications above and below ground: — polybutene (PB); — polyethylene (PE); — polyethylene of raised temperature resistance (PE-RT); — crossli nked polyethylene (PE-X); — polypropylene (PP). NOTE 1 Requirements for industrial valves are given in this International Standard and/or in other standards. Valves are to be used with components conforming to this International Standard provided that they conform additionally to the relevant requirements of this International Standard. This International Standard is applicable to either PB, PE, PE-RT, PE-X, or PP pipes, fittings, valves, and their joints and to joints with components of other plastics and non-plastic materials, depending on their suitability, intended to be used for the conveyance of liquid and gaseous fluids as well as solid matter in fluids for industrial applications such as the following: — chemical plants;…

ISO 9838-2015 pdf free.Alpine and touring ski-bindings一Test soles for ski-binding tests. ISO 9838 defines test soles representing — an alpine ski-boot (form A) or at least the bottom part of it to be used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465, and — a touring ski-boot (form T) or at least the bottom part of it to he used for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465. NOTE Ski-boots have their own International Standards (ISO 5355 and ISO 9523) that allow relatively large tolerances in defining the test sole which are generally believed to be suitable for on-slope use by skiers, but too large for reproducible laboratory measurements. 2 Normative references The following documents, in whole or in part. are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) ISO 5355, Alpine ski-boots — Requirements and test methods ISO 9462, Alpine ski-bindings — Requirements…

ISO 9972-2015 pdf free.Thermal performance of buildings – Determination of air permeability of buildings 一 Fan pressurization method. ISO 9972 is intended for the measurement of the air permeability of buildings or parts of buildings in the field. It specifies the use of mechanical pressurization or depressurization of a building or part of a building. It describes the measurement of the resulting air flow rates over a range of indoor-outdoor static pressure differences. This International Standard is intended for the measurement of the air leakage of building envelopes of single-zone buildings. For the purpose of this International Standard, many multi-zone buildings can be treated as single-zone buildings by opening interior doors or by inducing equal pressures in adjacent zones. International Standard does not address evaluation of air permeability of individual components. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7345, Thermal insulation — Physical quantities and definitions 3 Terms, definitions, and symbols 3.1 Terms and definitions For the purposes of this documcnt,…

ISO 10406-1-2015 pdf free.Fibre-reinforced polymer (FRP) rein forcement of concrete – Test methods – Part 1: FRP bars and grids. This part of ISO 10406 specifies test methods applicable to fibre-reinforced polymer (FRP) bars and grids as reinforcements or pre-stressing tendons in concrete. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 291:2008, Plastics — Standard atmospheres for conditioning and testing ISO 3611, Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics ISO 4788, Laboratory glassware — Graduated measuring cylinders ISO 7500-1, Metallic materials — Verification ofstaticuniaxialtesting machines— Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system ISO 13385-1, Geometrical product specfications (GPS) — Dimensional measuring equipment — Part 1: Callipers; Design and met rological characteristics 3 Terms, definitions, and symbols 3.1 Terms and definitions For the purposes oithis document, the tollowing terms and delinitions apply. 3.1.1 alkalinity condition of having or containing hydroxyl (01-I-) ions; containing alkaline substances Note 1…

ISO/TS 37151-2015 pdf free.Smart community infrastructures 一 Principles and requirements for performance metrics. This Technical Specification gives principles and specifies requirements for the — definition, — identification, — optimization, and — harmonization of community Infrastructure performance metrics, and gives recommendations for analysis, including — smartness, — interoperability. — synergy, — resilience, — safety,and — security of community infrastructures. Community infrastructures include, hut are not limited to, energy, water, transportation, waste, and ICT. The principles and requirements of this Technical Specification are applicable to communities of any size sharing geographic areas that are planning, commissioning, managing, and assessing all or any element of its community infrastructures. However, the selection and the importance of metrics or (key) performance indicators of community infrastructures is a result of the application of this Technical Specification and depends on the characteristics of each community. In this Technical Specification, the concept of smartness is addressed in terms of performance relevant to technologically implementable solutions, in accordance with sustainable development and resilience of communities as defined in ISO/TC 268. 2 Normative references There are no normative references. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 community group of people…

ISO/TR 44000-2019 pdf free.Principles for successful collaborative business relationship management. This document introduces twelve collaborative relationship management principles. ISO 44001 and related ISO collaborative management standards are based on the understanding and acknowledgement of these principles. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 44001, Collaborative business relationship management systems — Requirements and framework 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 44001 apply. ISO and IEC maintain terminological databases for use in standardization at the lollowing addresses: — ISO Online browsing platform: available at https://www.iso.org/ohp — IEC Electropedia: available at http://www.electropcdia.org/ 4 Relationship management Statement: A formalized process to manage and sustain collaborative relationships underpins their success. Rationale: To be sustainable over time, a collaborative relationship needs to be based on systems and processes, whether internal or jointly developed, together with a continued focus on monitoring and developing competence and behaviours. Key benefits: Collaborative relationships that are…

ISO 22322-2015 pdf free.Societal security一Emergency management一Guidelines for public warning. ISO 22322 provides guidelines for developing, managing, and implementing public warning before, during, and after incidents. This International Standard is applicable to any organization responsible for public warning. It is applicable at all levels, from local up to international. Before planning and implementing the public warning system, risks and consequences of potential hazards are assessed. This process is not part of this International Standard. 2 Normative references ISO 22300, Societal security — Terminology 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 22300 and the following apply. 3.1 alert part of public warning (31) that captures attention of first responders and people at risk (3J) in a developing emergency situation 3.2 all clear message or signal that the danger is over 3.3 hazard monitoring [unction activities to obtain evidence-based information on hazards in a defined area used to make decisions about the need for public warning (31) 3.4 warning dissemination function activities to issue appropriate messages for people at risk (3) based on evidence-based information received from the hazard monitoring function (3,3) 3.5 notification part of public warning (31) that provides essential information…

ISO/IEC 20933-2016 pdf free.Information technology – Distributed Application Platforms and Services (DAPS)一Access Systems. ISO/IEC 20933 specifies: 1) an ID triggered modular access system, the functions of the modules and the messages they exchange, and the sequence of messages, i.e. transitions of the transaction; 2) the system responsibility from receiving an access request until sending the result. i.e. a complete transaction: 3) the responsibilities of the modules, including time stamping and responding to the requests they received; and 4) the sequence and semantics of the messages and their elements. 2 Conformance Conformant Access Systems progress transactions by evaluating the applicable rules. Conformant modules implement the requests on their interfaces, the corresponding responses and time stamping as specified herein. 3 Normative references None. 4 Terms, definitions and acronyms For the purposes of this document, the following terms, definitions and acronyms apply. 4.1 ID Identifier 4.2 RED Rule Evaluation and Dispatching 4.3 transaction request for access 5 Model Figure 1 illustrates the Access System structure. The Access System has 5 modules “Access-point, Policy, Processing, RED and Storage” and 4 interfaces “Access-interface, Policy-interface, Processing-interface and Storage-interface”. The Access System progresses a transaction by exchanging messages between modules and decides the final result (grant or…