ISO 14230-2-2013 pdf free.Road vehicles – Diagnostic communication over K-Line (DoK- Line)一 Part 2: Data link layer. This part of ISO 14230 specifies data link layer services tailored to meet the requirements of UART based vehicle communication systems on K-Line as specified in ISO 14230-1. It has been defined in accordance with the diagnostic services established in ISO 14229-1 and ISO 15031-5, but is not limited to use with them, and is also compatible with most other communication needs for in-vehicle networks. The protocol specifies an unconfirmed communication. The diagnostic communication over K-Line (DoK-Line) protocol supports the standardized service primitive interface as specified in ISO 14229-2. This part of ISO 14230 provides the data link layer services to support different application layer implementations like: – enhanced vehicle diagnostics (emissions-related system diagnostics beyond legislated functionality,non-emissions-related system diagnostics); – emissions-related OBD as specified in IS0 15031, SAE ]1979-DA, and SAE J2012-DA. In addition, this part of ISO 14230 clarifies the differences in initialization for K-line protocols defined in IS09141 and ISO 14230. This is important since a server supports only one of the protocols mentioned above and the client has to handle the coexistence of all protocols during the protocol-determination procedure. 2…

BS ISO 15037-2:2002 pdf free download.Road vehicles – Vehicle dynamics test methods – Part 2: General conditions for heavy ve hicles and buses. This part of ISO 15037 specifies the general conditions that apply when vehicle dynamics properties are determined according to ISO test methods carried out on heavy vehicles. These are commercial vehicles, combinations, buses and articulated buses, as defined in ISO 3833 for trucks and trailers above 3,5 t and buses above 5 t maximum weight, and in UNECE (United Nations Economic Commission for Europe) and EC vehicle classification, categories M3, N2, N3, 03 and 04. In particular, it specifies general conditions for variables. measuring equipment and data processing, — environment (test track and wind velocity), test vehicle preparation (tuning and loading). initial driving, and test reporting (general data and test conditions), which are of general significance, independent of the specific vehicle dynamics test procedure. They apply when vehicle dynamics properties are determined, unless other conditions are required by the standard actually used for the test method. NOTE The general conditions defined in existing vehicle dynamics standards are valid up until the point wten a respective reference to this part of ISO 15037 is included. 2 Normative references…

ISO 3808-2002 pdf free download.Road vehicles一Unscreened high-voltage ignition cables一General specifications, test methods and requirements. ISO 3808 specifies the classes, types and dimensions of, and test methods and requirements for, unscreened high-voltage ignition cables used in spark-ignited engines for road vehicles. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 1817:1999, Rubber, vulcanized — Determination of the effect of liquids ISO 4926:1978, Road vehicles — Hydraulic brake systems — Non-petroleum base reference fluids 3 General cable specifications 3.1 Cable classes Depending on the test temperature for the thermal overload test (see 4.9) six cable classes are specified. See Table 1. 3.2 Cable types The type of cable depends on the conductor used. See Table 2. 4 Tests and requirements 4.1…

ISO 17215-3-2014 pdf free.Road vehicles – Video communication interface for cameras (VCIC) 一 Part 3: Camera message dictionary. ISO 17215-3 is based on the conventions specified in the OSI service conventions (ISO/IEC°10731) as they apply for physical layer, protocol, network, and transport protocol and diagnostic services. 5 Overview of ISO 17215 5.1 General This International Standard has been established in order to implement a standardized video communication interface for cameras on a communication data link. The focus of this International Standard is using existing protocols. — Figure 1 specifies the relation to the other parts of this International Standard. — Figure 2 specifies the relation of this International Standard to existing protocols. 5.2 Document overview and structure This International Standard consists of a set of four sub-documents, which provide all references and requirements to support the implementation of a standardized video communication interface for cameras according to the standard at hand. — ISO 172 15-1 provides an overview of the document set and structure along with use case definitions and a common set of resources (definitions, references) for use by all subsequent parts. — ISO 172 15-2 specifies the discovery and control of services provided by a VCIC camera. —…

ISO 20653-2013 pdf free.Road vehicles – Degrees of protection (IP code)一Protection of electrical equipment against foreign objects,water and access. This International Standard applies to degrees of protection (IP code) provided by enclosures of the electrical equipment of road vehicles. It specifies the following: a) Designations and definitions of types and degrees of protection provided by enclosures of electrical equipment (IP codes) for the: — protection of electrical equipment within the enclosure against ingress of foreign objects, including dust (protection against foreign objects); — protection of persons against access to hazardous parts inside the enclosure (protection against access); — protection of electrical equipment inside the enclosure against effects due to ingress of water (protection against water. b) Requirements for each degree of protection. c) Tests to be carried out in order to confirm that the enclosure complies with requirements of the relevant degree of protection. 2 Normative references The following referenced documents are indispensable for the application this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 12103-1, Road vehicles — Test dust for filter evaluation — Part 1: Arizona test dust I EC 60068-2-68, EnvIronmental…

ISO 16750-2-2012 pdf download.Road vehicles – Environmental conditions and testing for electrical and electronic equipment —Part 2: Electrical loads. This part of IS0 16750 applies to electric and electronic systems/components for road vehicles. Thispart of lSO 16750 describes the potential environmental stresses and specifies tests and requirementsrecommended for the specific mounting location on/in the road vehicle. This part of IS016750describes the electrical loads. Electromagnetic compatibility(EMC) is not coveredby this part of lS0 16750.Electrical loads are independent from the mounting location, but can vary dueto the electrical resistance in the vehicle wiring harness and connection system. 2Normative references The following referenced documents are indispensable for the application of this document.For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenceddocument (including any amendments) applies. ISO 8820 (all parts), Road vehicles —Fuse-links IS0 16750-1,Roadvehicles—Environmental conditions and testing forelectrical and electronicequipment一Part 1: General ISO 16750-4，Road vehicles ― Environmental conditions and testing for electrical and electronicequipment- Part 4 : Climatic loads 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 16750-1 apply. 4 Test and requirements 4.1 General lf not otherwise specified, the following tolerances shall apply: – frequency and time:…

ISO 16750-3-2012 pdf download.Road vehicles — Environmental conditions and testing for electrical and electronic equipment—Part 3:Mechanical loads. This part of ISO 16750 applies to electric and electronic systems/components for road vehicles. Itdescribes the potential environmental stresses and specifies tests and requirements recommended forthe specific mounting location on/in the vehicle. This part of ISO 16750 describes mechanical loads. 2Normative references The following referenced documents are indispensable for the application of this document.For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenceddocument (including any amendments) applies. ISO16750-1,Road vehicles—Environmental conditions andtesting for electricalandelectronic equipmentPart 1: General IEC 60068-2,6,Environmental testing — Part 2-6:Testing, Test Fc: Vibration (Sinusoidal) IEC60068-2,14,Basic environmental testing procedures—Part2-14:Tests—Test Nb:Changeof temperature gaa-bcnrc IEC 60068-2,64, Environmental testing —Part 2-64:Test methods —Test Fh — Vibration, broad-band random (digital control) and guidance IEC 60068-2,80,Environmental testing —Part 2-80:Tests —Test Fi: Vibration —Mixed mode testingIEC 60068-2-31,Environmental testing procedures — Part 2:Tests;Test Ec: Free fall,Clause 5.2 3Terms and definitions For the purposes of this document, the terms and definitions given in ISO 16750-1 apply. 4 Tests and requirements 4.1Vibration 4.1.1 General The vibration test methods specified consider various levels of vibration severities applicable to on-board electrical and electronic equipment. It is recommended…

ISO 7637-2-2011 pdf free.Road vehicles – Electrical disturbances from conduction and coupling – Part 2: Electrical transient conduction along supply lines only. This part of ISO 7637 specifies test methods and procedures to ensure the compatibility to conducted electrical transients of equipment installed on passenger cars and commercial vehicles fitted with 12 V or 24 V electrical systems. It describes bench tests for both the injection and measurement of transients. It is applicable to all types of road vehicles independent of the propulsion system (e.g. spark ignition or diesel engine, electric motor). Function perfomance status classification for immunity to transients is given in Annex A. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7637-1, Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 7637-1 apply. 4 Test procedure 4.1 General Methods for measuring the transient emission on supply lines and test methods for the immunity of…

ISO 6487-2012 pdf free download.Road vehicles – Measurement techniques in impact tests – Instrumentation. ISO 6487 gives requirements and recommendations for measurement techniques involving the instrumentation used in impact tests carried out on road vehicles. Its requirements are aimed at facilitating comparisons between results obtained by different testing laboratories, while its recommendations will assist such laboratories in meeting those requirements. It is applicable to instrumentation including that used in the impact testing of vehicle subassemblies. It does not include optical methods, which are the subject of ISO 8721. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2041, Mechanical vibration, shock and condition monitoring — Vocabulary ISO 3784, Road vehicles — Measurement of impact velocity in collision tests ISO 4130, Road vehicles — Three-dimensional reference system and fiducial marks — Definitions ISOITR 27957, Road vehicles — Temperature measurement in anthropomorphic test devices — Definition of the temperature sensor locations SAE J21 1-1:2007, Instrumentation for impact test — Part 1: Electronic instrumentation 3 Terms and definitions For the purposes of this document,…

ISO 6722-2-2013 pdf free.Road vehicles- 60 V and 600 V single-core cables – Part 2: Dimensions, test methods and requirements for aluminium conductor cables. This part of Iso 6722 specifies the dimensions, test methods, and requirements for single-core 60 V cables intended for use in road vehicle applications where the nominal system voltage is  60 V d.c. or 25 V a.c. It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications, where the nominal system voltage is from > 60 V d.c. or 25 V a.c. to 600 V d.c. or 600 V a.c. It also applies to individual cores in multi-core cables. This part of ISO 6722 specifies requirements for aluminium conductor cables. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6722-1, Road vehicles — 60 V and 600 V single-core cables — Part 1: Dimensions, test methods and requirements for copper conductor cables ISO 6892-1, Metallic materials — Tensile testing…