BS ISO 18197:2015 pdf free.Space systems一Space based services requirements for centimetre class positioning. BS ISO 18197 defines the requirements for the wide area centimetre class positioning system by broadcasting augmentation data through satellites as follows. — Centimetre class positioning According to the progress of requirements for positioning services such as automatic farming, mapping and others, centimetre class positioning is very useful. — Wide area positioning It is quite effective to broadcast augmentation data through satellites for users over wide area such as a square, more than 1,000 km each side, anytime and anywhere. Even if this area is short of data network, additional ground network facilities are not needed. In addition, as ranging signal and augmentation data can be received from satellite broadcasting at the same time, it is unnecessary for user terminals to receive the signal such as transmitted by ground network. — Real-time property The user terminals need to resolve the ambiguity in real-time, using augmentation data broadcast from satellites or other means, for the realization of centimetre class positioning. On the other hand, the provider sides have to broadcast augmentation data such that the terminal sides are able to resolve the ambiguity in real-time. 2 Normative references…

BS ISO 18118:2015 pdf free.Surface chemical analysis – Auger electron spectroscopy and X-ray photoelectron spectroscopy一Guide to the use of experimentally determined relative sensitivity factors for the quantitative analysis of homogeneous materials. BS ISO 18118 gives guidance on the measurement and use of experimentally determined relative sensitivity factors for the quantitative analysis of homogeneous materials by Auger electron spectroscopy and X-ray photoelectron spectroscopy. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 18115, Surface chemical analysis — Vocabulary ISO 21270, Surface chemical analysis — X-ray photoelectron andAuger electron spectrometers — Linearity of intensity scale 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 18115 and the following apply. absolute elemental sensitivity factor coefficient for an element by which the measured intensity for that element is divided to yield the atomic concentration or atomic fraction of the element present in the sample Note ito entry: The choice of use of atomic concentration or atomic fraction should be…

BS ISO 18074:2015 pdf free.Textiles – ldentification of some animal fibres by DNA analysis method一Cashmere, wool, yak and their blends. BS ISO 18074 specifies a testing method for DNA analysis of some animal fibres to identify cashmere, wool, yak, and their blends by using extraction, amplification by the polymerase chain reaction (PCR) method and DNA detection processes. This International Standard is applicable to cashmere, yak, and wool and their blends as a qualitative method. 2 Caution Test results for fibre identification by the DNA analysis method can be obtained with a high accuracy for the above-mentioned textile products which were processed at lower dye concentration levels or dyed in light colours. However, when such textile products were processed under severe conditions or high temperatures, the mitochondrial DNA could have been damaged. In such cases, identification can be difficult because amplification of DNA by PCR cannot take place. If textile products were contaminated by using products from another species, such as cashmere grease on wool fibres, this situation may be solved by checking using microscopy techniques. 3 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated…

BS ISO 4347:2015 pdf free.Leaf chains, clevises and sheaves一Dimensions, measuring forces, tensile strengths and dynamic strengths. BS ISO 4347 specifies the characteristics of chains used for general lifting purposes, together with the rim profiles of sheaves and the chain attachment ends of devises. It gives dimensions, limits for interchangeability, length measurement, preloading, minimum tensile strengths and minimum dynamic strengths. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 606, Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets ISO 156541), Fatigue test methods for transmission precision roller chains and leaf chains ASM E2) B29.8, Leaf chains, devises and sheaves 3 Chains 3.1 Nomenclature The nomenclature of chains is shown in Figure 1 (which does not necessarily define the actual form of the chain plates) and as given in Table 1 and Table 2. 3.2 Chain designation Leaf chain shall be designated by the prefix “LH”[“BL”] for chains derived from the ISO 606 A [ASME B29.8] series, or by the prefix“LL”for…

BS ISO 4079:2015 pdf free.Rubber hoses and hose assemblies – Textile-reinforced hydraulic types for oil-based or water-based fluids – Specification. BS ISO 4079 specifies requirements for five types of textile-reinforced hydraulic hose and hose assembly of nominal size from 5 to 100. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from -40 °C to +60 °C or oil-based hydraulic fluids H II, HL, HM, HR and HV as defined in Iso 6743-4 at temperatures ranging from —40 °C to +100 °C. This International Standard does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish compatibility of the hose with the fluid to be used. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters,…

BS ISO 3894:2015 pdf free.Road vehicles一Wheels/rims for commercial vehicles一Test methods. BS ISO 3894 specifies two laboratory methods for testing certain essential strength characteristics of disc wheels intended for road use on commercial vehicles, buses, trailers, and multipurpose passenger vehicles, as defined in ISO 3833. The test methods are — dynamic cornering fatigue test and — dynamic radial fatigue test. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3833, Road vehicles — Types — Terms and definitions ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 3911 and the following apply. 3.1 test bolt (fasteners) test bolt is a bolt that is attached to the hub/test fixture before mounting the wheel 3.2 wheel nut (fasteners) nut for fastening the wheel as a set with the test bolts (fasteners) (3d) 3.3 load rating value obtained by converting the force to mass which can…

ISO/DIS 14704-2015 pdf free.Fine ceramics [advanced ceramics, advanced technical ceramics)一Test method for flexural strength of monolithic ceramics at room temperature. ISO/DIS 14704 specifies a test method for determining the flexural strength of monolithic fine ceramics, and whisker- or particulate-reinforced ceramic composites, at room temperature and applies to materials with grain size less than 200 pm. This test method may be used for materials development, quality control, characterization and design data-generation purposes. NOTE Since fracture is due to tense stress, flexural strength data can be used to calculate a uniaxial tensile strength considering the effect of the tested volume and Weibull-statistics. So, flexural strength is often used in substitute for uniaxial tensile strength. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3611:1978. Micrometer callipers for external measurement ISO 7500-1:2004. Metallic materials — Verification of static uniaxia( testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. flexural strength maximum…

ISO 22034-2-2016 pdf free.Steel wire and wire products一 Part 2:Tolerances on wire dimensions. This part of ISO 22034 specifies the tolerances on the diameter of round wire and, where applicable, on the length of round wire cut to length, for bright (i.e. uncoated) steel wire, metallic-coated steel wire and non-metallic-coated steel wire. This part of ISO 22034 applies to round wires in the diameter range 0,050 mm to 25,00 mm. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6929, Steel products — Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6929 and the following apply. 3.1 wire product of constant cross section along its length, obtained by drawing a cold wire rod through a reducing die or passing it under pressure between rollers and rewinding the drawn product Note Ito entry: Wire can be supplied with a metallic or non-metallic coating, or with both, or without a coating. 3.2 cut length straightened…

ISO 22077-1-2015 pdf free.Health informatics – Medical waveform format一 Part 1: Encoding rules. ISO 22077-1 specifies how medical waveforms, such as electrocardiogram, electroencephalogram, spirometry waveform, etc., are described for interoperability among healthcare information systems. This International Standard may be used with other relevant protocols, such as HL7, DICOM, ISO/IEEE 11073, and database management systems for each purpose. This is a general specification, so specifications for particular waveform types and for harmonization with DICOM, SCP-ECG, X73, etc. are not given. This International Standard does not include lower layer protocols for message exchange. For example, a critical real-time application like a patient monitoring system is out of scope and this is an implementation issue. 2 Terms and definitions For the purposes o this document, the lollowing terms and detinitions apply. 2.1 frame waveform encoding unit consisting of data blocks, channels, and sequences 2.2 medical waveform time sequential data that are sampled by A/D converter or transmitted from medical equipment 2.3 sampling data that are converted at a fixed time interval channel individual waveform data group 4 Basic specifications 4.1 Basic attributes 4.1.1 General Medical waveform data described in accordance with the MFER consists of Sampling attributes (Figure 1), Frame attributes (Figure 2)…

ISO 19862-2015 pdf free.Buildings and civil engineering works一Sealants – Durability to extension compression cycling under accelerated weathering. ISO 19862 specifies a method for the determination of classilication of durability of sealants used in exterior joints in building construction. 2 Norniative reference The following documents, in whole or in part. are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated relereiwes, the latest edition of the referenced (locument (including any arnendmens) applies. ISO 4892-I I), Plastics — Methods of Exposure to Laboratory Lqht Sources — Part l General Guidance ISO 4892-2:2() 13, Plastics — Methods of exposure to lubaraloty light sources — Part 2: Xenon-arc lumps ISO 4892.32), Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UViamps ISO 4892-4, Plastics — Methods of exposure to laboratory light sources — Port 4: Open-flame carbon-arc laIfl$) ISO 6927, Buildinqs and civil enguieermq works — Seulants — Vocabulary ISO 13640, lluilthnq construction —Jointing products — Specificut ions for test substrates 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6927 apply. 4 Principle Test specimens are prepared such that…