ISO 15-2011 pdf free download.Rolling bearings一Radial bearings一 Boundary dimensions, general plan. ISO 15 specifies preferred boundary dimensions for radial bearings of the diameter series 7, 8, 9, 0, 1, 2, 3 and 4. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 464, Rolling bearings — Radial bearings with locating snap ring — Dimensions and tolerances ISO 582, Rolling bearings — Chamfer dimensions — Maximum values ISO 5593, Rolling bearings — Vocabulary ISO 12043, Rolling bearings — Single-row cylindrical roller bearings — Chamfer dimensions for loose rib and non-nb sides ISO 12044, Rolling bearings — Single-row angular contact ball bearings — Chamfer dimensions for outer ring non-thrust side ISO 15241, Rolling bearings — Symbols for quantities 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5593 apply. 4 Symbols For the purposes of this document, the symbols given in ISO 15241 and the following apply. The symbols shown in Figure 1 and given in Tables 1 to 8 denote nominal dimensions, unless specified…

ISO 15241-2012 pdf free.Rolling bearings – Symbols for physical quantities. ISO 15241 establishes the presentation of symbols for physical quantities (dimensions,dimensional tolerances,accuracy, load ratings，life, etc.) in the field of rolling bearings. These symbols areprimarily intended for use in International Standards and IlSo documents relating to rolling bearings, but theyare also suitable for use in other printed materials, such as handbooks,illustrations/drawings and pamphlets, 2Normative references The following documents, in whole or in part, are normatively referenced in this document and are dispensablefor its application.For dated references, only the edition cited applies.For undated references, the latest editionof the referenced document (including any amendments) applies. IsO 281, Rolling bearings – Dynamic load ratings and rating life ISO 1132-1，Rolling bearings — Tolerances — Part 1: Terms and definitionsISO 5593,Rolling bearings — Vocabulary IsO 80000-1,Quantities and units – Part 1: General IS0 80000-2,Quantities and units —Part 2:Mathematical signs and symbols to be used in the natural sciencesand technology 3Terms and definitions For the purposes of this document, the terms and definitions given in ISO 281,ISO 1132-1 and IS0 5593 apply. 4Symbols for physical quantities 4.1Principles of the system of symbols The following principles apply in this International Standard. – Generally, the principles of the system…

ISO 492-2014 pdf free.Rolling bearings – Radial bearings – Geometrical product specifications (GPS) and tolerance values. ISO 492 specifies dimensional and geometrical characteristics, limit deviations from nominal sizes, and tolerance values to define the interface (except chamfers) of radial rolling bearings. Nominal boundary dimensions are defined in ISO 15, ISO 355121 and ISO 8443191. This International Standard does not apply to certain radial bearings of particular types (e.g. needle roller bearings) or for particular fields of application (e.g. airframe bearings and instrument precision bearings). Tolerances for such bearings are given in the relevant International Standards. Chamfer dimension limits are given in ISO 582. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 15, Rolling bearings — Radial bearings — Boundary dimensions, general plan ISO 582, Rolling bearings — chamfer dimensions — Maximum values ISO 1101. Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out ISO 5593, Rolling bearings — Vocabulary ISO 14405-1, Geometrical product specifications (GPS) —…

ISO 3245-2015 pdf free.Rolling bearings一Needle roller bearings with drawn cup and without innerring – – Boundary dimensions, geometrical product specifications [GPS] and tolerance values. ISO 3245 specifies the boundary dimensions and preferred dimensions to be used for drawn cup needle roller bearings without inner ring as well as the minimum chamfer dimension limits. Also specified are the closed end thickness dimensions for hearings with one closed end. In addition, dimensional tolerances for the needle roller complement bore diameter and tolerances for the drawn cup width are specified. Informative values for the tolerances for shaft raceway and housing bore are given in AnnexA. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1132-1, Rolling bearings — Tolerances — Part 1: Terms and definitions ISO 5593, Rolling bearings — Vocabulary ISO 10579, Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts ISO 14405-1, Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes ISO 15241, Rolling bearings — Symbols for physical…

ISO 15-2017 pdf free.Rolling bearings – Radial bearings – Boundary dimensions, general plan. This document specifies preferred boundary dimensions for radial bearings of the diameter series 7,8, 9, 0, 1, 2, 3 and 4. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document, For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 464, Rolling bearings — Radial bearings with locating snap ring — Dimensions, geometrical product specifications (GPS) and tolerance values ISO 5593, Rolling bearings — Vocabulary ISO 12043, Rolling bearings — Single-row cylindrical roller bearings — Chamfer dimensions for loose rib and non-rib sides ISO 12044, Rolling bearings — Single-row angular contact ball bearings — Chamfer dimensions for outer ring non-thrust side 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5593 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — IEC Electropedia: available at http://www.electropedia.org/ — ISO Online browsing platform: available at http://www.iso.org/oIm 4 Symbols For the purposes of this…