ISO 14063-2020 pdf free.Environmental management – Environmental communication- Guidelines and examples. This document gives guidelines to organizations for general principles, policy, strategy and activities relating to both internal and external environmental communication. It uses proven and well-established approaches for communication, adapted to the specific conditions that exist in environmental communication. It is applicable to all organizations regardless oltheir size, type, location, structure, activities, products and services, and whether or not they have an environmental management system in place. It can be used in combination with any of the ISO 14000 family of standards, or on its own. NOTE 1 A reference table to the ISO 14000 family Is provided In Annex A. NOTE 2 ISO 14020, ISO 14021, ISO 14024, ISO 14025 and ISO 14026 provide specific environmental communication tools and guidance relating to product labels and declarations. 2 Normative references There are no normative references in this document. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https://www.iso.org/obp — I EC Electropedia: available at http/,Lwww.electropedia.org/ 3.1 environmental communication process that an…

ISO 13934-2-2014 pdf free.Textiles一Tensile properties of fabrics – Part 2: Determination of maximum force using the grab method. This part of ISO 13934 specifies a procedure for the determination of the maximum force of textile fabrics known as the grab test. NOTE ISO 13934-1 describes the method known as the strip test. The method is mainly applicable to woven textile fabrics including fabrics which exhibit stretch characteristics imparted by the presence of an elastomeric fibre and mechanical or chemical treatment. It can be applicable to fabrics produced by other techniques. It is not normally applicable to geotextiles, nonwovens, coated fabrics, textile-glass woven fabrics, and fabrics made from carbon fibres or polyolefin tape yarns. The method specifies the determination of the maximum force of test specimens in equilibrium with the standard atmosphere for testing and of test specimens in the wet state. The method is restricted to the use of constant-rate-of-extension (CRE) testing machines. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 139,…

ISO 6947-2019 pdf free.Welding and allied processes一Welding positions. This document defines welding positions for testing and production, for butt and fillet welds, in all product forms. Annex A gives examples of the limits of the slope of a weld axis and the rotation of the weld face about the weld axis for welding positions in production welds. Annex B gives a comparison of this document and US designation systems for welding positions. 2 Normative references There are no normative references in this document. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https://www.iso.orgJobp — IEC Electropedia: available at http://www.electropedia.org/ 4 Welding positions 4.1 Main welding positions The main welding positions PA to PG are illustrated in Figure 1. 4.2 Welding positions and allowable deviations for testing Welding positions used during welding of a test piece shall not exceed ±50 in slope and ±100 in rotation from the main welding position. 4.3 Welding positions and ranges in production The main welding positions are referenced in other standards, e.g. the ISO 9606 series for…

ISO 6787-2018 pdf free.Assembly tools for screws and nuts – Adjustable wrenches. This document specifies the dimensions of adjustable wrenches and the admissible clearance of the adjustable jaw. It also specifies test conditions to test the suitability of tool performance. NOTE The wrenches covered by this document are the ones identified in ISO 1703:2005 under reference number 11 01 040. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1711-1, Assembly tools for screws and nuts — Technical specifications — Part 1: Handoperated wrenches and sockets 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https://www.iso.org/obp — IEC Electropedia: available at https://www.electropedia.org/ 4 Dimensions The dimensions are given in Table 1. Figure 1 shows only an example and should not influence the design of the wrench. 5 Technical specifications 5.1 Clearance of adjustable…

ISO 6358-2-2013 pdf free.Pneumatic fluid power一 Determination of flow-rate characteristics of components using compressible fluids – 一 Part 2: Alternative test methods. This part of ISO 6358 specifies a discharge test and a charge test as alternative methods for testing pneumatic fluid power components that use compressible fluids, i.e. gases, and that have internal flow passages that can be either fixed or variable in size to determine their flow-rate characteristics. However, this part of ISO 6358 does not apply to components whose flow coefficient is unstable during use, i.e. components that exhibit remarkable hysteretic behaviour (because they can contain flexible parts that deform under the flow) or that have an internal feedback phenomenon (such as regulators), or components that have a cracking pressure such as non-return (check) valves and quick-exhaust valves. In addition, it does not apply to components that exchange energy with the fluid during flow-rate measurement, e.g. cylinders, accumulators, etc. NOTE This part of ISO 6358 does not provide a method to determine if a component has hysteretic behaviour; ISO 6358-1 does provide such a method, Table 1 provides a summary of which parts of ISO 6358 can be applied to various components. Evaluation of measurement uncertainties is…

ISO 4577-2019 pdf free.Plastics – Polypropylene and propylene-copolymers – Determination of thermal oxidative stability in air一Oven method. This document specitics a method for the determination of the resistance of mouldcd test specimens of polypropylene and propylene-copolymers to accelerated ageing by heat in the presence of air using a forced draught oven. The method represents an attempt to estimate the service life of parts fabricated from propylene plastics. The stability determined by this method is not directly related to the suitability ot the material for use when difkrent environmental conditions prevail. NOTh The specified thermal levels arc considered sufficiently severe to cause failure of commercial grades of heat-stable propylene plastics within a reasonable period of time. If desired. lower temperatures can be applied to estimate the performance of propylene plastics with lower heat stabilities. 2 Normative references The following documents arc rcterrcd to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 291, Plastics — Standard atmospheres for conditioning and testing ISO 19069-2, Plastics — Polypropylene (P19 moulding…

ISO 3452-3-2013 pdf free.Non-destructive testing – Penetrant testing一 Part 3: Reference test blocks. ISO 3452-3 describes two types of reference blocks: Type I reference blocks are used to determine the sensitivity levels of both fluorescent and colour contrast penetrant product families: — Type 2 reference blocks are used for routine assessment of the performance of both fluorescent and colour contrast penetran( testing. The reference blocks are to be used in accordance with part I of this International Standard. 2 Normative references The following referenced documents, in whole or in part. are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10088- 1, Stainless steels — Part 1: List of standard stainless steels EN 10204, Metallic products — Tipes of inspection docwnenis ISO 4957, Tool steels ISO 10474. Steel and steel products Inspection documents ISO 155 10, Stainless steels Chemical composition 3 Description of reference blocks The Type I reference block consists of a set of four nickel-chrome plated panels with 10 pm, 20 pm, 30 pm and 50 pm thickness of plating, respectively. The 10…

ISO 6722-2-2013 pdf free.Road vehicles- 60 V and 600 V single-core cables – Part 2: Dimensions, test methods and requirements for aluminium conductor cables. This part of Iso 6722 specifies the dimensions, test methods, and requirements for single-core 60 V cables intended for use in road vehicle applications where the nominal system voltage is  60 V d.c. or 25 V a.c. It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications, where the nominal system voltage is from > 60 V d.c. or 25 V a.c. to 600 V d.c. or 600 V a.c. It also applies to individual cores in multi-core cables. This part of ISO 6722 specifies requirements for aluminium conductor cables. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6722-1, Road vehicles — 60 V and 600 V single-core cables — Part 1: Dimensions, test methods and requirements for copper conductor cables ISO 6892-1, Metallic materials — Tensile testing…

ISO/DIS 6509-2-2014 pdf free.Corrosion of metals and alloys一Determination of dezincification resistance of copper alloys with zinc 一 Part 2: Acceptance criteria. This Part of ISO 6509 specifies acceptance criteria for the selection of dezincification resistant copper alloys with a mass fraction of zinc of more than 15 %, exposed to fresh, saline waters or drinking water. The acceptance criteria are based on the exposure tests in ISO 6509-1. The materials tested and accepted can be in the form of a semi-finished product or in the form of a final product (fittings, valves etc.). This standard is not applicable to complex products like flow-meters or pump-parts. In addition, other properties of the material might need to be taken into account for the intended application. This standard is not intended to validate dezincification in case of failure in the application. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8044, Corrosion of metals and alloys — Basic terms and definitions ISO 6509-1 Corrosion of metals…

ISO 4628-1-2016 pdf free.Paints and varnishes – Evaluation of degradation of coatings一 Designation of quantity and size of defects, and of intensity of uniform changes in appearance一 Part 1: General introduction and designation system. This part of ISO 4628 defines a system for designating the quantity and size of defects and the intensity of changes in appearance of coatings and outlines the general principles of the system used throughout ISO 4628. This system is intended to be used, in particular, for defects caused by ageing and weathering. and for uniform changes, for example yellowing. The other parts of ISO 4628 provide pictorial standards or other means for evaluating particular types of defect. As far as possible, already existing evaluation schemes have been used as the basis. This part of ISO 4628 is also used for assessing defects not covered by the other parts of ISO 4628. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 13076, Paints and varnishes — Lighting and procedure…