ISO 9838-2015 pdf free.Alpine and touring ski-bindings一Test soles for ski-binding tests.
ISO 9838 defines test soles representing
— an alpine ski-boot (form A) or at least the bottom part of it to be used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465, and
— a touring ski-boot (form T) or at least the bottom part of it to he used for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465.
NOTE Ski-boots have their own International Standards (ISO 5355 and ISO 9523) that allow relatively large tolerances in defining the test sole which are generally believed to be suitable for on-slope use by skiers, but too large for reproducible laboratory measurements.
2 Normative references
The following documents, in whole or in part. are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer
(Shore hardness)
ISO 5355, Alpine ski-boots — Requirements and test methods
ISO 9462, Alpine ski-bindings — Requirements and test methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5355 and the following apply.
3.1 test sole form A test sole for testing alpine ski-bindings
3.2 test sole form T test sole for testing touring ski-bindings
3.3 test sole type A test sole for adults In accordance with ISO 5355, type A, suitable for bindings of type A (adults) and CA (junior) in accordance with ISO 9462
3.4 test sole type C test sole for children in accordance with ISO 5355, type C. suitable for bindings of type C (children) in accordance with ISO 9462
3.5 basic test sole one-piece sole of length 305 mm for type A and 255 mm for type C
3.6 variable length soles sole that is either adjustable, in two parts, or a set of several fixed length soles between 270 mm and 360 mm for type A and between 200 mm and 280 mm for type C
4 Material and manufacture
The sole shall be moulded in polyurethane (TPU) reinforced by a metal insert in order to achieve the mechanical requirements given in Clause 6. It is moulded in a homogeneous material and in a mould with the same roughness on the sole/binding interface to ensure that the friction coefficient is the same all over this interface. In the shell areas, reinforcement is allowed to support the walls. It should remain outside the flat area. Form T could be based, for example, on the same construction as form A type A with the addition of a TPU part to allow tooling of the defined profile in Figure 3 and glueing of a thick rubber sole of hardness 68 ± 5 Shore A. The dimensions of test sole form T which are not given in Figure 3 shall be taken from test sole form A type A shown in Figure 1.
5 Dimensions
The dimensions of the basic sole shall be as shown in Figures 1 to . Except for the overall length, all the dimensions also apply to the variable length soles subject to the tolerance in Table 1.ISO 9838 pdf free download.
Tags: Test soles for ski-binding tests
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…