ISO 8536-9-2015 pdf free.Infusion equipment for medical use – Part 9: Fluid lines for single use with pressure infusion equipment. This part of Iso 8536 applies to sterilized fluid lines for single use for use with pressure infusion equipment up to a maximum of 200 kPa (2 bar). The following items are covered by this part of Iso 8536: a) syringe pump lines (SPL); b) connecting lines (CL); c) lines with integrated injection cannula (LIC). In some countries, the national pharmacopoeia or other national regulations are legally binding and take precedence over this part of ISO 8536, 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 594-2,1)Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment — Part 2: Lock fittings ISO 7000, Graphical symbols for use on equipment — Registered symbols ISO 7864, Sterile hypodermic needles for single use ISO 8536-4:2010, Infusion equipment for medical use — Part 4: Infusion sets for single use, gravity feed ISO…

ISO 15675-16-2016 pdf free.Cardiovascular implants and artificial organs – Cardiopulmonary bypass systems – Arterial blood line filters. This document specifies requirements for sterile, single-use, arterial blood line filters intended to filter and remove emboli, debris, blood clots and other potentially hazardous solid and gaseous material from the blood of humans during cardiopulmonary bypass surgery. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 594-2, Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment — Part 2: Lock fittings ISO 10993-1, Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk management process ISO 10993-4, Biological evaluation of medical devices — Part 4: Selection of tests for interaction with blood ISO 10993-7, Biological evaluation of medical devices — Part 7. Ethylene oxide sterilization residuals ISO 10993-11, Biological evaluation of medical devices — Part 11: Tests for systemic toxicity ISO 11135, Sterilization of health-care products — Ethylene oxide — Requirements…

ISO 8575-2016 pdf free.Aerospace一Fluid systems一Hydraulic system tubing. This document provides information relating to the sizes and materials of tubing for use in aerospace hydraulic pressure and return and suction lines. For pressure lines, the requirements apply to the pressure and temperature ranges covered by pressure class D. E and I and temperature type 13 and type 20 as specified in Iso 6771. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8574, Aerospace — Hydraulic system tubing — Qualification tests for bent tubes ISO 6771, Aerospace — Fluid systems and components — Pressure and temperature classifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: • IEC Electropedia: available at http://www.electropedia.orgj.. • ISO Online browsing platform: available at http://www.iso.org/obp/ 3.1 inch — tubing tubing diameters and wall thickness in fractional inch increments and based on industry standards…

ISO 8536-10-2015 pdf free.Infusion equipment for medical use – Part 10: Accessories for fluid lines for single use with pressure infusion equipment. This part of Iso 8536 applies to sterilized accessories for single use in fluid lines and pressure infusion equipment as specified in ISO 8536-8. This part of ISO 8536 includes the following: a) two-way stopcocks, three-way stopcocks, four-way stopcocks, and stopcocks manifold; NOTE Designation of a stopcock depends on the number of connections. The number of possible functional positions can be expressed by addition of a complementary note, using a diagonal stroke and a numeral indicating the number of possible stopcock positions, e.g. 3/4-way stopcock for three-way stopcock with four possible positions. b) units with injection site or check valve; c) stoppers or adapters. In some countries, the national pharmacopoeia or other national regulations are legally binding and take precedence over this part of ISO 8536. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 594-2’), Conical fittings with 6 %…

ISO 4823-2015 pdf free.Dentistry一Elastomeric impression materials. This International Standard specifies the requirements and tests that the state-of-the art body of knowledge suggests for helping determine whether the elastomeric impression materials, as prepared for retail marketing, are of the quality needed for their intended purposes. NOTE This International Standard does not address possible biological hazards associated with the materials. Therefore, interested parties are encouraged to explore ISO 7405 and ISO 10993 for assessment of such hazards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1942, Dentistry一Vocabulary ISO 6873, Dentistry一Gypsum products 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1942 and the following apply. 3.1 consistency degree of firmness with which particles of a material, prepared for use, cohere so as to allow the material to flow, or resist flow, as required to achieve the purpose for which it is intended 3.2 elastic recovery test DEPRECATED: compression set DEPRECATED: permanent deformation DEPRECATED: recovery from deformation…

ISO 4628-7-2016 pdf free.Paints and varnishes – Evaluation of degradation of coatings一 Designation of quantity and size of defects, and of intensity of uniform changes in appearance一 Part 7: Assessment of degree of chalking by velvet method. This part of Iso 4628 specifies a method suitable, in particular, for rating the degree of chalking on white or coloured exterior coatings and coating systems on rough surfaces (i.e. those having a roughness greater than segment 4 of the reference comparator G as described in ISO 8503-1). The test method specified can also be used for the assessment of the degree of chalking of coatings and coating systems on smooth surfaces, but the method specified in ISO 4628-6:2011 is preferable for this purpose. The test method is applicable to coatings and coating systems on mineral substrates, e.g. fibre cement, brick, concrete, and renderings, independent of the structure of the surface. The method can be used quite effectively by experienced operators and is recommended for laboratory use as well as for on- site evaluation. NOTE I When a reference to this test method is included In specifications, the test conditions (I.e. weathering method and substrate) have to be agreed between the interested parties….

ISO 4628-5-2016 pdf free.Paints and varnishes – Evaluation of degradation of coatings – Designation of quantity and size of defects, and of intensity of uniform changes in appearance一 Part 5: Assessment of degree of flaking. This part of Iso 4628 specifies a method for assessing the degree of flaking of coatings by comparison with pictorial standards. ISO 4628-1 defines the system used for designating the quantity and size of defects and the intensity of changes in appearance of coatings and outlines the general principles of the system. This system is intended to be used, in particular, for defects caused by ageing and weathering, and for uniform changes such as colour changes, for example yellowing. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Iso 13076, Paints and varnishes — Lighting and procedure for visual assessments of coatings 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 degree of flaking rating characterizing flaked areas in a coating…

ISO 4406-2017 pdf free.Hydraulic fluid power – Fluids – Method for coding the level of contamination by solid particles. This document specifies the code to be used in delining the quantity of solid particles in the llLIi(1 used in a given hydraulic fluid power system. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements ol this document. For dated rekreiwes, oniy the ediUon cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4407, !!draulic Jhiid power — Fluid contuminut ion — Determination vi particulate cofltuminutwn by the countinq met hod using an optical microscope ISo 11171. hydraulic fluid power — Calibration of automatic particle counters for liquids ISO 11500, Hydraulic fluid power — Determination of the particulate contamnmafion level of a liquid samnplc by automatic particle counting using the liqhtcxtinctiomi principle 3 Code definition 3.1 General The purpose of this code is to simplify the reporting of particle count data by converting the numbers of particles into broad classes or codes, where an increase in one code is generally a doubling of the contamination level. The…

AS ISO 7457:2021 pdf free.Earth-moving machinery一Determination of turning dimensions of wheeled machines. AS ISO 7457 specifies methods for determining the turning radius, turning diameter, machine clearance diameter, and inside and outside tyre clearance diameters, described in the horizontal plan by a wheeled earth-moving machine with its equipment and attachments when executing a turn. This International Standard is applicable to all types of steerable wheeled earth-moving machinery. It is applicable irrespective of the type of steering used. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of I EC and ISO maintain registers of currently valid International Standards. ISO 50 10:1992, Earth-moving machinery — Rubber-ty red machines — Steering requirements. ISO 6165:1997, Earth-moving machinery — Basic types — Vocabulary. ISO 9248:1992, Earth-moving machinery — Units for dimensions, performance and capacities, and their measurement accuracies. 3 Definitions For the purposes of this International Standard, the definitions given in…

AS ISO 7451:2021 pdf free.Earth-moving machinery – Volumetric ratings for hoe-type and grab-type buckets of hydraulic excavators and backhoe loaders. AS ISO 7451 specifies a method for estimating the volume of materials which a hoe- type or grab-type bucket of a hydraulic excavator or backhoe loader can normally contain. The volume assessments are based on the internal dimensions of the bucket and on the representative volumes at the top of the bucket. The method employs the technique of dividing the complex shape of the material in the bucket into simple geometric shapes. This method of assessment is intended to provide a conventional means of comparing bucket capacities. It is not intended to be used to define true capacities. This International Standard is not applicable to buckets of cable excavators. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 hydraulic excavator self-propelled machine on crawlers, wheels or legs, having an upper structure capable of a 3600 swing with mounted equipment and which is primarily designed for excavating with a bucket, without movement of the undercarriage during the work cycle Note I to entry: An excavator work cycle normally comprises excavating, elevating, swinging and…