ISO 15638-2015 pdf free.Intelligent transport systems – Framework for cooperative telematics applications for regulated vehicles (TARV)一Part 15: Vehicle location monitoring. This part of ISO 15638 addresses the provision of ‘vehicle location monitoring’and specifies the form and content of such data required to support such systems and access methods (42) to that data. The scope of this part of ISO 15638 is to provide specifications (4.42) for common communications and data exchange aspects of the application service (44) vehicle location monitoring that a regulator (4.38) may elect to require or support as an option, including a) high-level definition of the service that a service provider (4AQ) has to provide, NOTE The service definition describes common service elements; but does not define the detail of how such an application service (44) is instantiated, not the acceptable value ranges of the data concepts defined. b) means to realize the service, and c) application data, naming content, and quality that an IVS (4.26) has to deliver. The definition of what comprises a ‘regulated’ service is regarded as an issue for national decision, and may vary from jurisdiction (42w to jurisdiction. This International Standard does not impose any requirements on nations in respect of which…

BS EN ISO 12759:2015 pdf free.Fans一Efficiency classification for fans. BS EN ISO 12759 establishes a classification of fan efficiency for all fan types driven by motors with an electrical input power range from 0.125 kW to 500 kW. This International Standard is applicable to bare shaft and driven fans, as well as fans integrated into products. Fans integrated into products are measured as stand-alone fans. This International Standard is not applicable to; a) fans for smoke and emergency smoke extraction; b) fans for industrial processes; c) fans for automotive application, trains and planes; d) fans for potentially explosive atmospheres; e) box fans, powered roof ventilators and air curtains: 1) jet fans for use in car parks and tunnel ventilation, 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5801:2007, industrial fans — Performance testing using standardized airways ISO 13348:2007, Industrial fans — Tolerances, methods of conversion and technical data presentation ISO 13349:2010, Fans — Vocabulaiy and definitions of categories IEC 60034-2-1, Rotating electrical machines — Part 2-1: Standard methods for determining…

BS EN ISO 9687:2015 pdf free.Dentistry一Graphical symbols for dental equipment. The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Iso 639-1, Codes for the representation of names of languages — Part 1: Alpha-2 code ISO 1942, Dentistry — Vocabulary ISO 8601, Data elements and interchange formats — Information interchange — Representation of dates and times ISO 15223-1:2012, Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Part 1: General requirements ISO 17724, Graphical symbols — Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1942, ISO 15223-1 and ISO 17724 apply. 4 Requirements 4.1 General Graphical symbols used to convey the information given in Clause 5 are given in this International Standard. In orderto arrange for the user of this International Standard all symbols necessary for dental equipment are shown in this International Standard. Therefore, some symbols defined by other International Standards are given for information purposes together with…

ISO 9687-2015 pdf free.Dentistry一Graphical symbols for dental equipment. ISO 9687 specifies graphical symbols for dental equipment. It is intended that the symbols are to be used on the appropriate piece of dental equipment and in documents pertaining to dental equipment, for example in instructions for use, marking, labelling, and technical product documentation. The symbols are selected specifically for all kinds of dental equipment. The majority of the symbols are taken from relevant ISO, IEC, or other international documents. Several new symbols presented by manufacturers or users have been added. NOTE In addition to terms used in two of the three official ISO languages (English, French, and Russian), this International Standard gives the equivalent terms in the German language; these are published under the responsibility of the member body for Germany (DIN). However, only the terms given in the official languages can be considered as ISO terms. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 639-1, Codes for the representation of names of…

ISO 7626-2-2015 pdf free.Mechanical vibration and shock – Experimental determination of mechanical mobility一 Part 2: Measurements using single-point transl ation excitation with an attached vibration exciter. This part of ISO 7626 specifies procedures for measuring linear mechanical mobility and other frequency- response functions of structures, such as buildings, machines and vehicles, using a single-point translational vibration exciter attached to the structure under test for the duration of the measurement. It is applicable to measurements of mobility, accelerance, or dynamic compliance, either as a driving- point measurement or as a transfer measurement. It also applies to the determination of the arithmetic reciprocals of those ratios, such as free effective mass. Although excitation is applied at a single point, there is no limit on the number of points at which simultaneous measurements of the motion response may be made. Multiple-response measurements are required, for example, for modal analyses. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2041, Mechanical vibration, shock and condition monitoring —…

ISO 2320-2015 pdf free.Fasteners一Prevailling torque steel nuts – Functional properties. ISO 2320 specifies the functional properties for prevailing torque steel nuts when tested at an ambient temperature range of +10 °C to +35 °C. It includes a combined test method to determine the prevailing torque properties and the torque/clamp force properties at the same time. It applies to prevailing torque all metal type nuts and prevailing torque non-metallic insert type nuts: — with triangular ISO thread in accordance with ISO 68-1; — with diameter/pitch combination in accordance with ISO 261 and ISO 262; — with coarse pitch thread M5 to M39 or with fine pitch thread M8 x ito M39 x 3; — with thread tolerances in accordance with ISO 965-2; — with mechanical properties in accordance with ISO 898-2; Prevailing torque values specified in this standard are based on laboratory test conditions. NOTE I Actual prevailing torques in practical application can vary. NOTE 2 All metal type nuts conforming to the requirements of this International Standard are used in applications ranging from -50°C to +150 °C. NOTE 3 Non-metallic insert type nuts conforming to the requirements of this International Standard are used In applications ranging from -50 °C to…

BS ISO 18413:2015 pdf free.Hydraulic fluid power一 Cleanliness of components 一Inspection document and principles related to contaminant extraction and analysis, and data reporting. BS ISO 18413 specifies the content of an inspection document that specifies both the cleanliness requirement for the specified hydraulic fluid power component and the inspection method to be used for evaluating its cleanliness level. In addition, guidelines for relevant extraction methods and analysis methods are given. Determination of what constitutes as an appropriate cleanliness level requirement for any particular component is beyond the scope of this International Standard. ISO 12669 provides a method of determining the required cleanliness of a hydraulic system. ISO TR 10686 provides a method of relating the required cleanliness of components to the required cleanliness of the hydraulic system. For the purposes of this International Standard, approved functional liquids are considered to be components. This International Standard is applicable to the particulate contamination on the wetted surfaces and volumes of any hydraulic fluid power system component. Appearance defects and liquid or gaseous contamination are not covered by this International Standard. This International Standard does not address safety problems that might arise from hazardous materials, operations, and equipment associated with its use. The…

BS ISO 16745:2015 pdf free.Environmental performance of buildings一Carbon metric of a building一Use stage. BS ISO 16745 provides requirements for determining and reporting a carbon metric of an existing building, associated with the operation of the building. It sets out methods for the calculation, reporting, communication, and verification of a set of carbon metrics for GHG emissions arising from the measured energy use during the operation of an existing building, the measured user-related energy use, and other relevant GHG emissions and removals. These carbon metrics are separated into three measures designated CM1, CM2, and CM3 (see 5.1.1). This International Standard follows the principles set out in ISO 15392 and those described in Clause 4. Where deviations from the principles in ISO 15392 occur, or where more specific principles are stated, this International Standard takes precedence. The carbon metrics CM1 and CM2 are not quantified based on life cycle assessment (LCA) methodology. Carbon metric CM3 may include partial quantification based on the results of LCA. This International Standard does not include any method of modelling of the operational energy use of the building but follows the conventions provided by other International Standards, as given in relevant clauses. This International Standard is not…

ISO 6347-2017 pdf free.Textile floor coverings – Consumer in forma tion. This document specifies the technical subjects that form the basis for the provision of information, at the point of sale, for consumer guidance prior to and after the purchase of a textile floor covering. It is applicable to textile floor coverings of all types. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1765, Machine-made textile floor coverings — Determination of thickness ISO 2076, Textiles — Man-made fibres — Generic names ISO 3018, Textile floor coverings — Rectangular textile floor coverings — Determination of dimensions ISO 6938, Textiles — Naturalfibres — Generic names and definitions ISO 8543, Textile floor coverings — Methods for determination of mass ISO 24342, Resilient and textile floor-coverings — Determination of side length, edge straightness and squareness of tiles 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at…

ISO 7438-2016 pdf free.Metallic materials – Bend test. ISO 7438 specifies a method for determining the ability of metallic materials to undergo plastic deformation in bending. This International Standard applies to test pieces taken from metallic products, as specified in the relevant product standard. It is not applicable to certain materials or products, for example tubes in full section or welded joints, for which other standards exist. 2 Symbols and designations Symbols and designations used in the bend test are shown in Figures 1 and 2 and specified in Table 1. 3 Principle The bend test consists of submitting a test piece of round, square, rectangular or polygonal cross- section to plastic deformation by bending, without changing the direction of loading, until a specified angle of bend is reached. The axes of two legs of the test piece remain in a plane perpendicular to the axis of bending. In the case of a 1800 bend, the two lateral surfaces may, depending on the requirements of the product standard, lie flat against each other or may be parallel at a specified distance, an insert being used to control this distance. 4 Test equipment 4.1 General The bend test shall be carried…