ISO 22034-2-2016 pdf free.Steel wire and wire products一 Part 2:Tolerances on wire dimensions. This part of ISO 22034 specifies the tolerances on the diameter of round wire and, where applicable, on the length of round wire cut to length, for bright (i.e. uncoated) steel wire, metallic-coated steel wire and non-metallic-coated steel wire. This part of ISO 22034 applies to round wires in the diameter range 0,050 mm to 25,00 mm. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6929, Steel products — Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6929 and the following apply. 3.1 wire product of constant cross section along its length, obtained by drawing a cold wire rod through a reducing die or passing it under pressure between rollers and rewinding the drawn product Note Ito entry: Wire can be supplied with a metallic or non-metallic coating, or with both, or without a coating. 3.2 cut length straightened…

ISO 22077-1-2015 pdf free.Health informatics – Medical waveform format一 Part 1: Encoding rules. ISO 22077-1 specifies how medical waveforms, such as electrocardiogram, electroencephalogram, spirometry waveform, etc., are described for interoperability among healthcare information systems. This International Standard may be used with other relevant protocols, such as HL7, DICOM, ISO/IEEE 11073, and database management systems for each purpose. This is a general specification, so specifications for particular waveform types and for harmonization with DICOM, SCP-ECG, X73, etc. are not given. This International Standard does not include lower layer protocols for message exchange. For example, a critical real-time application like a patient monitoring system is out of scope and this is an implementation issue. 2 Terms and definitions For the purposes o this document, the lollowing terms and detinitions apply. 2.1 frame waveform encoding unit consisting of data blocks, channels, and sequences 2.2 medical waveform time sequential data that are sampled by A/D converter or transmitted from medical equipment 2.3 sampling data that are converted at a fixed time interval channel individual waveform data group 4 Basic specifications 4.1 Basic attributes 4.1.1 General Medical waveform data described in accordance with the MFER consists of Sampling attributes (Figure 1), Frame attributes (Figure 2)…

ISO 19862-2015 pdf free.Buildings and civil engineering works一Sealants – Durability to extension compression cycling under accelerated weathering. ISO 19862 specifies a method for the determination of classilication of durability of sealants used in exterior joints in building construction. 2 Norniative reference The following documents, in whole or in part. are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated relereiwes, the latest edition of the referenced (locument (including any arnendmens) applies. ISO 4892-I I), Plastics — Methods of Exposure to Laboratory Lqht Sources — Part l General Guidance ISO 4892-2:2() 13, Plastics — Methods of exposure to lubaraloty light sources — Part 2: Xenon-arc lumps ISO 4892.32), Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UViamps ISO 4892-4, Plastics — Methods of exposure to laboratory light sources — Port 4: Open-flame carbon-arc laIfl$) ISO 6927, Buildinqs and civil enguieermq works — Seulants — Vocabulary ISO 13640, lluilthnq construction —Jointing products — Specificut ions for test substrates 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6927 apply. 4 Principle Test specimens are prepared such that…

ISO 19242-2015 pdf free.Rubber- Determination of total sulfur content by ion chromatography. ISO 19242 specifies a method for the determination of the total sulfur content of raw rubber and unvulcanized or vulcanized rubber compounds by ion chromatography following the preparation of a sample solution using either a tubular furnace combustion or an oxygen combustion flask method. The tubular furnace combustion method is applicable for rubbers with sulfur content less than 0,1 % as it is possible that the oxygen combustion flask method will not give sufficiently accurate results. The oxygen combustion flask method is not applicable to rubbers containing a metal salt that forms an insoluble metal sulfate, such as barium sulfate. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3696, Water for analytical laboratory use — Specification and test methods ISO 1795, Rubber, raw natural and raw synthetic — Sampling and further preparative procedures ISO 4661-2, Rubber, vulcanized — Preparation of samples and test pieces — Part 2: Chemical tests 3…

ISO 18314-1-2015 pdf free.Analytical colorimetry – Part 1: Practical colour measurement. This part of ISO 18314 specifIes the method for determining the colour coordinates of a paint film. This method is only applicable to paint films that appear to be uniformly of one colour, i.e. monochromatic, when examined with normal vision. Paint films that do not completely hide a non-transparent substrate represent an opaque system and can be measured by using the procedure in this part of ISO 18314. Luminescent paint films, transparent paint films, and translucent paint films (for example for display or lamp glass), retroreflecting paint films (for example for traffic signs), and metallic paint films are outside the scope of this part of ISO 18314. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1513, Paints and varnishes — Examination and preparation of test samples ISO 1514, Paints and varnishes — Standard panels for testing ISO 2808, Paints and varnishes — Determination offilm thickness ISO 15528, Paints, varnishes and raw…

ISO 18070-2015 pdf free.Corrosion of metals and alloys一Crevice corrosion formers with disc springs for flat specimens or tubes made from stainless steel. ISO 18070 specifies a crevice forming technique and crevice former which are intended to be used for crevice corrosion testing of flat specimens or tubes of stainless steels, in corrosive solutions. Tb is International Standard specifies no in format ion concerning how the crevice corrosion testing shall he pertormed and how the attack shall be evaluated. The crevice former specified in this International Standard can be used for electrochemical measurements, ii the specimens are designed for electrical connections. 2 Normative references The following documents, in whole or in part. are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3696, Wuter for analytical luborcaory use — Specification and test niethods ISO 8044, Corrosion of metals and alloys — Basic terms and definitions ISO 6344-3, coated abrasives — Grain size analysis — Part 3: l)etermination of qrain size distribution of nicrogrits P240 to i’2500 DIN 2093, Disc springs — Quality specifications — Dimensions 3…

ISO 17850-2015 pdf free.Photography一Digital cameras  – Geometric distortion (GD) measurements. ISO 17850 specifies a protocol to measure geometric distortion of a digital camera. It is applicable to the measurement of digital cameras including camera phones. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 14524, Photography — Electronic still-picture cameras — Methods for measuring opto-electronic conversion functions (OECFs). IEC 61146-1, Video cameras (PAL/SECAM/NTSC) — Methods of measurement — Part 1: Non-broadcast single-sensor cameras EBU Tech3249, Measurement and analysis of the performance offilm and television camera lenses 3 Terms and definitions 3.1 geometric distortion GD <of DSC> displacement from the ideal shape of a subject (lying on a plane parallel to the image plane) in the recorded image Note I to entry: Geometric distortion basically derives from variation of lateral magnification in the image field of a camera lens and results in straight lines being rendered as curves. There are other factors to induce geometric distortion, for example, rotational asymmetricity of a camera lens…

ISO/IEC 11801-5-2017 pdf free.Information technology – Generic cabling for customer premises – Part 5: Data centres. This part of ISO/IEC 11801 specifies generic cabling within and to the computer room spaces of data centre premises, or data centre spaces within other types of buildings. It covers balanced cabling and optical fibre cabling. This document is optimized for premises in which the maximum distance over which telecommunications services can be distributed is 2 000 m. The principles of this document can also be applied to larger installations. Cabling specified by this document supports a wide range of services including voice, data and video that can also incorporate the supply of power. This document specifies directly or via reference to lSO/IEC 11801-1 a) the structure and minimum configurations for generic cabling within data centres, b) the interfaces at the equipment outlet (EO) and the external network interface (ENI), c) the performance requirements for cabling links and channels, d) the implementation requirements and options, e) the performance requirements for cabling components, f) the conformance requirements and verification procedures. Safety (e.g. electrical safety and protection, fire) and electromagnetic compatibility (EMC) requirements are outside the scope of this document, and are covered by other standards…

ISO 25745-3-2015 pdf free.Energy performance of lifts, escalators and moving walks – Part 3: Energy calculation and classification of escalators and moving walks. This part of Iso 25745 specifies a) generic tools for estimating energy consumption of escalators and moving walks, and b) a consistent method for energy performance classification of existing, modernized, or new escalators and moving walks. This part of ISO 25745 considers the energy performance during the operational portion of the life cycle of escalators and moving walks. It does not cover energy consumption and classification of the ancillary equipment, such as the following: a) lighting with the exception of comb plate lighting, step gap lighting, and traffic light; NOTE I Comb plate lighting, step gap lighting, and traffic light are considered essential for the operation of the equipment and are therefore not defined as ancillary equipment. b) cooling and heating and machine room ventilation; c) alarm devices and emergency battery supplies equipment. etc.; d) environmental conditions; e) consumption through the power sockets. NOTE 2 There can be other electrical loads not associated with the escalator or moving walk, which shall not be included. This part of ISO 25745 considers all escalators and inclined moving walks up…

ISO 24234-2015 pdf free.Dentistry一Dental amalgam. ISO 24234 specifies the requirements and test methods for dental amalgam alloys that are suitable for the preparation of dental amalgam, together with the requirements and test methods for that dental amalgam and the requirements for packaging and marking (including those for dental mercury). It is applicable to dental amalgam alloys supplied in the form of a free-flowing powder in bulk, or a powder compressed to form a tablet, or a powder in a capsule (i.e. pre-capsulated). With respect to dental mercury, the scope is limited solely to dental mercury which is supplied precapsulated or in pre-dosed sachets. Both are limited to a mass sufficient for one mix. The mass of dental mercury in one capsule or sachet shall be sufficient to produce a homogeneous plastic mix, appropriate for a small or medium sized restoration in a single tooth. This International Standard is not applicable to mercury supplied in masses greater than this in a single primary container (i.e. dental mercury in bulk). Dental mercury supplied in bulk volumes will not conform to this International Standard. This International Standard does not exclude the supply of dental amalgam alloy or dental mercury separately. This International Standard…