AS ISO 8813:2021 pdf free.Earth-moving machinery一Lift capacity of pipelayers and wheeled tractors or loaders equipped with side boom. AS ISO 8813 provides a uniform method of calculating, and a test method for validating, rated lift capacity as presented in commercial literature for pipelayers and wheeled tractors or loaders equipped with a vertical-only pivoted, hydraulic or mechanically operated, side boom. The rated lift capacity considers hoist mechanism limits, tipping loads and rope factor. After the lift capacity has been calculated and validated, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or wheeled machine configuration. This International Standard applies to machines having a lift capacity greater than 10 000 N when used in lifting applications. It includes pipelayers as defined in ISO 6165 and ISO 7136, and wheeled tractors and loaders as defined in ISO 6165, ISO 6747 and ISO 7131. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the…

AS/NZS IEC 60331.2:2021 pdf free.Tests for electric cables under fire conditions一Circuit integrity. This part of IEC 60331 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 v/i 000 V, including those of rated voltage below 80 V, metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables of not greater than 20 mm overall diameter. Cables of larger diameter are intended to be tested using the apparatus, procedure and requirements of IEC 60331-i. This document includes details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 viiooo V. Details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-2. Although the scope is restricted to cables with rated voltage up to and including 0,6/1,0 kV, the procedure can be used, with the…

AS ISO 10987.3:2021 pdf free.Earth-moving machinery一Sustainability Part 3: Used machines. This document gives requirements and relevant information for evaluating used earth-moving machines. It provides the means to evaluate a used machine, relative to the information provided by the manufacturer in the operator’s manual, in order to verify that the used machine is functional as intended by the manufacturer. This document is applicable to earth-moving machines as defined in ISO 6165 that are used and are planned to be resold. NOTE The used machine might not meet all current standards and regulations (e.g. roading and hazardous environments). 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6165, Earthmoving machinery — Basic types — Identification and terms and definitions ISO 10987, Earth-moving machinery — Sustainability — Terminology, sustainability factors and reporting 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6165, ISO 10987 and the following apply. 4.1 General The requirements in…

AS ISO 10987:2021 pdf free.Earth-moving machinery一Sustainability 一Terminology, sustainability factors and reporting. AS ISO 10987 sets out general principles for addressing the sustainability of the earth- moving machinery defined in ISO 6165. It establishes a sustainability terminology, identifies significant sustainability factors for earth-moving machines and provides an example of a reporting format for sustainability Information. This International Standard is applicable to the development and manufacturing processes and the useful life and end-of-life of earth-moving machines, 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies ISO 5349-2, Mechanical vibration — Measurement and evaluation of human exposure to hand-transmitted vibration — Part 2: Practical guidance for measurement at the workplace ISO 6165, Earth-moving machinery — Basic types — Identification and terms and definitions ISO 6395, Earth-moving machinery — Determination of sound power level — Dynamic test conditions ISO 6396, Earth-moving machinery — Determination of emission sound pressure level at operator’s position — Dynamic test conditions ISO 14040, Environmental management — Life cycle assessment — Principles and framework…

AS/NZS 5263.1.8:2021 pdf free.Gas appliances Part 1.8: Decorative effect gas appliances. AS/NZS 5263.1.8 provides specific requirements and test methods for Type 1 and Type 2 decorative effect gas appliances with natural draught or fan assisted combustion systems, with an energy input not exceeding 72 Mi/h. For Australia, the fuel gases are natural gas (as described by AS 4564), town gas, liquefied petroleum gas (LP Gas, as described by AS 4670), simulated natural gas (SNG) and tempered liquefied petroleum gas (TLP). For New Zealand, the fuel gases are natural gas (as specified in NZS 5442) and general product liquefied petroleum gas (NZLPG) (as specified in NZS 5435). NOTE 1 Space heating appliances are not covered by this Standard but are covered by the requirements of AS/NZS 5263.1.3. NOTE 2 Indoor flueless appliances are not covered by this Standard. NOTE 3 Appliances falling within the scope of AS 2658 are not covered by this Standard. NOTE 4 Other statutory or regulatory requirements may be applicable to a product that falls within the scope of this Standard. It is the responsibility of the manufacturer, importer or distributor (as appropriate) to ensure that products conform to such requirements. Test methods are set out in…

AS 5227.1:2021 pdf free.Cranes – Requirements for mechanisms Part 1: General (ISO 10972-1:1998, MOD). This part of ISO 10972 establishes requirements which apply generally to mechanisms and related components of cranes and lifting appliances as described in ISo 4306-1, ISO 4306-2 and ISO 4306-3. Requirements concern: a) general layout and design of mechanisms; b) selection and/or design requirements of components; c) instructions for manufacture, mounting, installation and testing. Rules for proof of competence calculation regarding different limit states (yield strength, fatigue, wear) are excluded from this part of ISO 10972. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 10972. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 10972 are encouragedto investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 1328-1:1995, Cylindrical gears一ISO system of accuracy一Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth. ISO 2408:1985, Steel wire ropes for general purposes一Characteristics. ISO 3077:- -1), Short…

AS ISO 19880.8:2021 pdf free.Gaseous hydrogen一Fuelling stations Part 8: Fuel quality control. This document specifies the protocol for ensuring the quality of the gaseous hydrogen at hydrogen distribution facilities and hydrogen fuelling stations for proton exchange membrane (PEM) fuel cells for road vehicles. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 19880-1, Gaseous hydrogen一Fuelling stations一Part 1: General requirements 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 5 Hydrogen specifications The quality requirements of hydrogen fuel dispensed to PEM fuel cells for road vehicles are listed in ISO 14687-2. 6 Quality control approaches 6.1 General There are two common methods to control the quality of hydrogen at a fuelling station, by spot sampling and continuous monitoring. These methods can be used individually or together to ensure hydrogen quality levels. 6.2 Sampling Spot sampling at a fuelling station involves capturing a measured amount for chemical analysis. Sampling is used to perform…

AS 61869.2:2021 pdf free.INSTRUMENT TRANSFORMERS – Part 2: Additional requirements for Current Transformers. This part of IEC 61869 is applicable to newly manufactured inductive current transformers for use with electrical measuring instruments and/or electrical protective devices having rated frequencies from 15 Hz to 100 Hz. 2 Normative references Clause 2 of IEC 61869-1:2007 is applicable with the following additions: IEC 61869-1:2007, Instrument Transformers — Part 1: General requirements 3 Terms and definitions For the purposes of this document, the terms and definitions in IEC 61869-1:2007 apply with the following additions: 3.1 General definitions 3.1.20 1 current transformer instrument transformer in which the secondary current, under normal conditions of use, is substantially proportional to the primary current and differs in phase from it by an angle which is approximately zero for an appropriate direction of the connections (SOURCE: IEC 60050-321:1986, 321-02-011 3.1.202 measuring current transformer current transformer intended to transmit an information signal to measuring instruments and meters (SOURCE: IEC 60050-321:1986, 321-02-18] 3.1.203 protective current transformer a current transformer intended to transmit an information signal to protective and control devices (SOURCE: IEC 60050-321: 1986. 321-02-19) 3.1.204 class P protective current transformer protective current transformer without remanent flux limit, for which the…

AS 5235.1:2021 pdf free.Cranes – Information labels Part 1: General (ISO 9942-1:2015, MOD). This part of ISO 9942 specifies the minimum requirements for labels for the identification (marking) and the operation of cranes. 2 ldentification data 2.1 Manufacturer’s data As a minimum, the fllowing information shall figure permanently on every crane: name of the supplier; name of the manufacturer; year of manufacture; serial number; model. 2.2 Loading data Information on the maximum loadings (capacities) shall figure permanently on the crane and be easily legible. This information is also required to avoid overloading; see the other parts of ISO 9942. 3 Information on operation of the crane by the crane operator 3.1 Control installations and indicating devices The information shall be attached where it is easily visible. Further information shall be available in the product-specific standards. 3.2 Tasks of the crane operator Information relating to the tasks of the crane operator on or near the control installations of cranes shall include information about his tasks prior to, during and after crane operation. This shall be in the form of a permanently attached label in the cab, or at the operator’s station if there is no control platform.If there is no control…

AS 3450:2021 pdf free.Earth-moving machinery一Wheeled or high-speed rubber-tracked machines 一Performance requirements and test procedures for brake systems (ISO 3450:2011, MOD). AS 3450 specifies minimum performance requirements and test procedures for the service, secondary and parking brake systems of wheeled and high-speed rubber-tracked earth-moving machines, for the uniform assessment of those brake systems. It is applicable to the following earth-moving machinery, operating on work sites or in mining, or travelling on public roads: — self-propelled, rubber-tyred earth-moving machines, as defined in ISO 6165; — sell-propelled rollers and landfill compactors, as defined in ISO 6165 and ISO 8811; — self-propelled scrapers, as defined in ISO 7133; — remote-control machines, as defined in ISO 6165, wheeled or rubber-tracked; — derivative earth-moving machines with rubber tyres; — earth-moving machines with rubber tracks and a maximum machine speed 20 km/h. It is not applicable to pedestrian-controlled earth-moving machinery (see ISO 17063) or crawler earth- moving machines with steel or rubber tracks that travel at <20 km/h (see ISO 10265). While purpose- built underground mining machines are not within the scope of this International Standard, its provisions can generally be applied to those machines with some braking performance modifications and additions (see Annex A). NOTE At…