ISO 128-24-2014 pdf free.Technical drawings – General principles of presentation – Part 24: Lines on mechanical engineering drawings. This part of ISO 128 specifies general rules and basic conventions for the types of lines on mechanical engineering drawings. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 128-20:1996, Technical drawings — General principles of presentation — Part 20: Basic conventions for lines ISO 128-22:1999, Technical drawings — General principles of presentation — Part 22: Basic conventions and applications for leader lines and reference lines ISO 128-30:200 1, Technical drawings — General principles of presentation — Part 30: Basic conventions for views ISO 128-40:2001, Technical drawings — General principles of presentation — Part 40: Basic conventions for cuts and sections ISO 128-50:2001, Technical drawings — General principles of presentation — Part 50: Basic conventions for representing areas on cuts and sections ISO 129-1, Technical drawings — Indication of dimensions and tolerances — Part 1: General principles ISO 1101:2012, Geometrical product specifications (GPS) — Geometrical…

ISO 5817-2014 pdf free.Welding一Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded)一Quality levels for imperfections. ISO 5817 provides quality levels of imperfections in fusion-welded joints (except for beam welding) in all types of steel, nickel, titanium and their alloys. It applies to material thickness  0,5 mm. It covers fully penetrated butt welds and all fillet welds. Its principles can also be applied to partial-penetration butt welds. (Quality levels for beam welded joints in steel are presented In ISO 139 19-1.) Three quality levels are given in order to permit application to a wide range of welded fabrication. They are designated by symbols B, C and 0. Quality level B corresponds to the highest requirement on the finished weld. Several types of loads are considered, e.g. static load, thermal load, corrosion load, pressure load. Additional guidance on fatigue loads is given in Annex C. The quality levels refer to production and good workmanship. This International Standard is applicable to a) non-alloy and alloy steels, b) nickel and nickel alloys, c) titanium and titanium alloys, d) manual, mechanized and automatic welding, e) all welding positions. f) all types of welds. e.g. butt welds, fillet welds and branch connections,…

ISO 5832-11-2014 pdf free.Implants for surgery一Metallic material ls – Part 11: Wrought titanium 6-aluminium 7-niobium alloy. This part of ISO 5832 specifies the characteristics of, and corresponding test methods for, the wrought titanium alloy known as titanium 6-aluminium 7-niobium alloy (Ti-6-Al 7-Nb) for use in the manufacture of surgical implants. NOTE The mechanical properties of a sample obtained from a finished product made of this alloy might not necessarily comply with those specified in this part of ISO 5832. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature ISO 20160:2006, Implants for surgery — Metallic materials — Classification of microstructures for alpha÷beta titanium alloy bars 3 Chemical composition The heat analysis shall conform to the requirements as to the chemical composition prescribed in Table 1. Ingot analysis can be used for reporting all chemical requirements except hydrogen, which shall be determined after the heat treatment and pickling procedure….

ISO 5359-2014 pdf free.Anaesthetic and respiratory equipment一Low-pressure hose assemblies for use with medical gases. ISO 5359 specifies requirements for low-pressure hose assemblies intended for use with the following medical gases: — oxygen, — nitrous oxide, — medical air, — helium, — carbon dioxide, — xenon, — specified mixtures of the gases listed above, — oxygen-enriched air, — air for driving surgical tools, — nitrogen for driving surgical tools, and for use with vacuum. 1.2 *It applies to hose assemblies operating at pressures up to 1 400 kPa and for vacuum systems at pressures not greater than 60 kPa absolute. 1.3 This International Standard does not specify the dimensions and allocation of the gas-specific inlet and outlet connectors for the hose assemblies. NOTE 1 Specifications for the dimensions and allocation of diameter index safety system (DISS) connectors are specified in CGA V-S 1281. NOTE 2 Specifications forthe dimensions and allocation of sleeve indexed system (S1S) connectors are specified in AS 2896 1231. NOTE 3 DimensIons and allocation of non-interchangeable screw-threaded (NIST) connectors are specified in ISO 18082 1111. NOTE 4 Terminal units designed for quick connectors are specified in ISO 9170-1. 1.4 This International Standard does not specify requirements for coaxial…

ISO 5011-2014 pdf free.Inlet air cleaning equipment for internal combustion engines and compressors – Performance testing. ISO 5011 establishes and specifies uniform test procedures, conditions, equipment, and a performance report to permit the direct laboratory performance comparison of air cleaners. The basic performance characteristics of greatest interest are air flow restriction or differential pressure, dust collection efficiency, dust capacity, and oil carry-over on oil bath air cleaners. This test code therefore deals with the measurement of these parameters. This International Standard is applicable to air cleaners used on internal combustion engines and compressors generally used in automotive and industrial applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5167-1, Measurement of fluid flow by means of pressure differential devices inserted in circular cross- section conduits running full — Part 1: General principles and requirements ISO 12103-1, Road vehicles — Test contaminants forfilter evaluation — Part 1: Arizona test dust 3 Terms and definitions 3.1 Terms, definitions, symbols and units For the purposes…

ISO 4017-2014 pdf free.Fasteners一Hexagon head screws – Product grades A and B. ISO 4017 specifies the characteristics of hexagon head screws with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10 d or 150 mm, whichever is the shorter, and product grade 13 for threads over M24 or nominal lengths over 10 d or 150 mm, whichever is the shorter. NOTE This type of product is the same as that covered by ISO 4014 with the exception of threading up to head and nominal lengths up to and including 200 mm as preferred lengths. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1. ISO 965-1, ISO 3506-1, ISO 4753 and ISO 4759-1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners — Bolts,…

ISO 8098-2014 pdf free.Cycles一Safety requirements for bicycles for young children. ISO 8098 specifies safety and performance requirements and test methods for the design, assembly and testing of fully assembled bicycles and sub-assemblies for young children. It also provides guidelines for instructions on the use and care of the bicycles. This International Standard is applicable to bicycles with a maximum saddle height of more than 435 mm and less than 635 mm, propelled by a transmitted drive to the rear wheel. It is not applicable to special bicycles intended for performing stunts (e.g. BMX bicycles). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1101, Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out ISO 5775-1, Bicycle tyres and rims — Part 1: 7re designations and dimensions ISO 5775 -2, Bicycle tyres and rims — Part 2: Rims ISO 6742-2, Cycles — Lighting and retro-reflective devices — Part 2: Ret ro-reflective devices ISO 11243, Cycles — Luggage carriers…

ISO 6506-1-2014 pdf free.Metallic materials- Brinell hardness ; test – Part 1: Test method. This part of Iso 6506 specifies the method for the Brinell hardness test for metallic materials. It is applicable to both fixed location and portable hardness testing machines. For some specific materials and/or products, particular International Standards exist (e.g. ISO 4498) and make reference to this International Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4498, Sintered metal materials, excluding hardmetals — Determination of apparent hardness and micro hardness ISO 6506-2:2014, Metallic materials — Brinell hardness test — Part 2: Verification and calibration of testing machines ISO 6506-3:2014, Metallic materials — Brinell hardness test — Part 3: Calibration of reference blocks ISO 6506-4, Metallic materials — Brinell hardness test — Part 4: Table of hardness values 3 Principle An indenter (tungsten carbide composite ball with diameter, U) is forced into the surface of a test piece and, after removal of the force, F, the diameter of the…

ISO 6362-2-2014 pdf free.Wrought aluminium and aluminium alloys – Extruded rods/bars, tubes and profiles一 Part 2: Mechanical properties. This part of Iso 6362 specifies the mechanical properties of wrought aluminium and aluminium alloy extruded rods/bars, tubes, and profiles for general engineering applications. It applies to extruded products. 2 Normative references The following documents, in whole or In part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6362-i. Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 1: Technical conditions for Inspection and delivery 150 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature ASTM B557M, Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium- Alloy Products 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6362-1 apply. 4 Tensile testing For the selection of the specimens and tensile testing, see ISO 6892-1 or ASTM BSS7M. 5 Mechanical properties Values for mechanical properties of aluminium and aluminium alloys are given in Tables ito…

ISO 6361-3-2014 pdf free.Wrought aluminium and aluminium alloys一Sheets, strips and plates一 Part 3: Strips: Tolerances on shape and dimensions. This part of Iso 6361 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy strip by cold-rolling for general engineering applications. It applies to products with thickness of over 0.15 mm up to, and including 16 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further roiling (reroll stock), or to special products such as those that are corrugated or embossed. Technical conditions for inspection and delivery of products covered by this part of ISO 6361 are specified in ISO 6361-1. 2 Dimensional tolerances 2.1 Thickness Thickness tolerances shall be in accordance with Tables 1 and 2.. When the tolerance is specified as either all plus, or minus side, the value in Table 1. or in Table 2. shall be doubled. Tolerances for the products exceeding the range of specified thickness and width shall he agreed upon by the purchaser and the supplier. 2.2 Width Width tolerances shall be in accordance with Table 3. When the tolerance is specified as either all plus, or minus side, the value in Table…