ISO 2020-1-1997 pdf free download.Aerospace一Preformed flexible steel wire rope for aircraft controls一 Part 1: Dimensions and loads. 6 Ropes 6.1 ConstructIon Wire ropes covered by this part of ISO 2020 are of the two types of construction shown in table 5. 6.1.1 7 x 7 construction This type of wire rope shall be composed of six outer strands each of seven wires laid in a right-hand direction around a steel centre strand of seven wires. The steel centre strand shall be composed of a layer of six wires laid in a right-hand direction around a core or king wire. It shall be of sufficient diameter to give full support to the outer strands. The six outer strands shall be composed of a layer of six wires laid in a left-hand direction around a core or king wire. The lengths of lay shall be as follows: a) the six outer strands shall be laid around the steel centre strand with a length of lay between six and eight times the nominal diameter of the rope; b) the lengths of lay of six wires of the steel centre strand and of the outer strands shall not exceed 60 % of the length…

ISO 7376-2020 pdf download.Anaesthetic and respiratory equipment一Laryngoscopes for tracheal intubation. This document, which is device-specific, specifies requirements for laryngoscopes with non-flexibi blades, with internal battery-operated power sources, used for illuminating the larynx dunn intubation. It also specifies critical dimensions for those handles and laryngoscope blades wit interchangeable hook-on fittings. It is not applicable to the following: — flexible laryngoscopes; — laryngoscopes designed for surgery; — laryngoscopes powered from mains electricity supply; — laryngoscopes connected by light-transmitting cables to external light sources; — video laryngoscopes designed to work with an external, integral or attached video system. 2 Normative references The following documents are referred to in the text in such a way that some or all of their conter constitutes requirements of this document. For dated references, only the edition cited applies. Fc undated references, the latest edition of the referenced document (including any amendments) applie ISO 4135, Anaesthetic and respiratory equipment — Vocabulary ISO 18190:2016, Anaesthetic and respiratory equipment — General requirements for airways and relate equipment IEC 60601-1-12:2014, Medical electrical equipment — Part 1-12: General requirements for basic safety an essential performance — Collateral Standard: Requirements for medical electrical equipment and medic electrical systems used in the emergency medical…

ISO 14063-2020 pdf free.Environmental management – Environmental communication一 Guidelines and examples. This document gives guidelines to organizations for general principles, policy, strategy and activities relating to both internal and external environmental communication. It uses proven and well-established approaches for communication, adapted to the specific conditions that exist in environmental communication. It is applicable to all organizations regardless of their size, type, location, structure, activities, products and services, and whether or not they have an environmental management system in place. It can be used in combination with any of the ISO 14000 family of standards, or on its own. NOTE 1 A reference table to the ISO 14000 family is provided in Annex A. NOTE 2 ISO 14020, ISO 14021, ISO 14024, ISO 14025 and ISO 14026 provide specific environmental communication tools and guidance relating to product labels and declarations. 2 Normative references ‘I’here are no normative references in this document. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https://www.iso.org/obp — IEC Electropedia: available at http://www.electropedia.org/ 3.1 environmental communication process that an…

ISO 1460-2020 pdf download.Metallic coatings – Hot dip galvanized coatings on ferrous materials一 Gravimetric determination of the mass per unit area. This document specifies a method of determining the mass per unit area of hot dip galvanized coatings on ferrous materials. Since an exact knowledge of the area of the surface is essential, this document is mainly applicable to shapes whose areas are easy to determine. If, with heavy samples, the specifications of Clause 7 cannot be met, then the hot dip galvanized coating mass is determined by another method. 2 Normative references There are no normative references in this document. 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the tollowing addresses: — ISO Online browsing platform: available at https://www.iso.org/obp — IEC Electropedia: available at http://www.electropedia.org,’ 4 Principle The hot dip galvanized coating on a surface of known area is dissolved in inhibited acid and the resultant loss in mass is determined by weighing the sample before and after the coating is dissolved. 5 Stripping solution Dissolve 3,5 g of hexamethylenetetramine in 500 ml of concentrated hydrochloric acid (p  1,18 g/ml). Dilute this…

ISO 7886-2-2020 pdf free.Sterile hypodermic syringes for single use一 Part 2: Syringes for use with power-driven syringe pumps. This document specifies requirements for sterile single-use hypodermic syringes of nominal capacity 1 ml and above, made of plastic materials and intended for use with power-driven syringe pumps. This document does not apply to syringes with auto-disable syringe features (ISO 7886.3121). syringes for use with insulin (ISO 8537131), single-use syringes made of glass, syringes prefilled with the injection by the manufacturer and syringes supplied with the injection as a kit for filling by a pharmacist. It does not address compatibility with injection fluids. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3696, Water for analytical laboratory use — Specification and test methods I SO 7886-1:2017, Sterile hypodermic syringes for single use — Part 1: Syringes for manual use ISO 80369-7, Small-bore connectors for liquids and gases in healthcare applications — Part 7. Connectors for intravascular or hypodermic applications ISO/IEC…

ISO 56005-2020 pdf free download.Innovation management – Tools and methods for intellectual property management一Guidance. 4.4 Culture The organization should promote an organizational culture that supports the effective management of IP. 4.41 Awareness For the effective establishment, implementation, maintenance, and continual improvement of the management of IP, the organization should promote IP awareness throughout the organization by: a) Obtaining oversight and approval from the organization’s top management of both policy and processes for the strategic management of lP; b) designating a member of the senior management team accountable for implementing the organization’s policy and processes for the management of IP; c) providing employees with an understanding of IP management policies and processes, their purpose and specific expectations related to their role requirements and how they contribute to the effectiveness of IP management in their day-to-day work operations; d) ensuring employees across all areas understand the IP specific business processes and methods, and the implications and consequences of not conforming to the organization’s requirements for the management of IP. 4.4.2 Work environment For the effective establishment, implementation, maintenance, and continual improvement of the management of lP. the organization should provide and maintain an enabling work environment by: a) encouraging all levels of…

ISO 13320-2020 pdf free.Particle size analysis- Laser diffraction methods. This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties. It does not address the specific requirements of particle size measurement of specific materials. This document is applicable to particle sizes ranging from approximately 0,1 lIm to 3 mm. With special instrumentation and conditions, the applicable size range can be extended above 3 mm and below 0,1 kim. For spherical and non-spherical particles, a size distribution is reported, where the predicted scattering pattern for the volumetric sum of spherical particles matches the measured scattering pattern. This is because the technique assumes a spherical particle shape in its optical model. For non-spherical particles the resulting particle size distribution is different from that obtained by methods based on other physical principles (e.g. sedimentation, sieving). 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the…

ISO 1833-18-2020 pdf download.Textiles一Quantitative chemical analysis一 Part 18: Mixtures of silk with wool or other animal hair (method using sulfuric acid). This document specifies a method, using sulfuric acid, to determine the mass percentage of silk, after removal of non-fibrous matter, in textiles made of mixtures of — silk with — wool or other animal hair. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1833-1, Textiles — Quantitative chemical analysis — Part 1: General principles of testing 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https://www.iso.org/obp — IEC Electropedia: available at http://www.electropedia.org/ 4 Principle The silk fibre is dissolved from a known dry mass of the mixture with a mass fraction of 75 % sulfuric acid. NOTE Wild silk, such as tussah silk, are not completely soluble in a mass fraction…

ISO 2409-2020pdf download.Paints and varnishes一Cross-cut test. The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1513, Paints and varnishes — Examination and preparation of test samples ISO 2808, Paints and varnishes — Determination offilm thickness ISO 4618, Paints and varnishes — Terms and definitions ISO 13076, Paints and varnishes — Lighting and procedure for visual assessments of coatings ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 4618 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https:/jwww.isoorg/obp — IEC Electropedia: available at http://www.electropedia.org/ 4 Principle Six parallel cuts are introduced in the coating and another six cuts are introduced perpendicular to the first cuts. Any loose paint particles are removed. The Cut area is examined visually and compared to a six-step classification. 5 Apparatus 5.1 General…

ISO 185-2020 pdf free download.Grey cast irons – CI assification. The material shall be designated as given in either Table 1 or Table 2. The designation system is given in ISO/TR 15931. The number in position 3 of the designation in Table 1 is the minimum tensile strength of the grade as determined by test pieces machined from standardized 30 mm test bars or from cast samples of corresponding relevant wall thickness. The number in position 3 of the designation in Table 2 is the maximum Brinell hardness value of the grade for relevant wall thickness > 40 mm to  80 mm. 5 Order information The following information shall be supplied by the purchaser: a) the complete designation of the material; b) any special requirements that have to be agreed between the manufacturer and the purchaser. All agreements between the manufacturer and the purchaser shall be made by the time of acceptance of the order. 6 Manufacture Unless otherwise specified by the purchaser, the method of manufacture of grey cast irons, including their chemical composition, to obtain the specified mechanical properties shall be left to the discretion of the manufacturer. The manufacturer shall ensure that the requirements of this…