BS ISO 13976:2016 pdf free.Hot-rolled steel sheet in coils of structural quality and heavy thickness. This document applies to hot-rolled carbon/manganese steel sheet in coils of structural quality without the use of microalloying elements. It is generally used in the delivered condition and is intended for bolted, riveted or welded structures. The product is produced on a wide sheet mill. The product is intended for structural purposes where particular mechanical properties are required. The steel sheet is produced in a number of grade designations designed to be compatible with differing application requirements. This document does not cover steels intended for boilers or pressure vessels, or steels designated as commercial quality or drawing qualities, or steels rolled to cold-reduced products, or steels designated as weathering steels, having increased atmospheric corrosion resistance, or those products rolled on a plate mill. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 148-1. Metallic materials — Charpy pendulum impact test — Part 1:…

BS ISO 9022-9:2016 pdf free.Optics and photonics一 Environmental test methods Part 9: Solar radiation and weathering. This part of Iso 9022 specifies the methods relating to the environmental tests of optical instruments including additional assemblies from other fields (e.g. mechanical, chemical and electronic devices). under equivalent conditions, for their ability to resist the effects of simulated solar radiation or laboratory weathering, which is a combination of simulated solar radiation, heat, and moisture. It is applicable to instruments that may be exposed to sunlight during operation or unsheltered storage on the earth’s surface, or in the lower atmosphere. The purpose of testing is to investigate to what extent the optical, climatic, mechanical, chemical and electrical (including electrostatic) performance characteristics of the specimen are affected by solar radiation or weathering (solar radiation, heat, and moisture). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4892-1:1999, Plastics — Methods of exposure to laborato,y light sources — Part 1: General guidance ISO 4892-2:2013, Plastics — Methods of…

ISO 19207-2016 pdf free. Thermal spraying . Classification method of adhesive strength by indentation. ISO 19207 specifies the classification method of adhesive strength for thermal spray coatings at room temperature by using Vickers hardness testing machine. This International Standard classifies the adhesive strength, called adhesion index, evaluated from the maximum indentation force without visible cracking, and it is applicable for relative dense metal coatings, ceramic coatings and cermet coatings. This International Standard can be used within comparison within each coating system. The indentation method is not recommended for very thin and very porous coatings and also for the coating system with lower cohesion strength than adhesion strength. It is recommended that this test method can be applied for a coating of which porosity is less than approximately 15 %. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method ISO 6507-2, Metallic materials — Vickers hardness test — Part 2: Verification and…

ISO 1304-2016 pdf free.Rubber compounding ingredients一Carbon black – Determination of iodine adsorption number. ISO 1304 specifies methods for the determination of iodine adsorption number of carbon blacks for use in the rubber industry. Two titration methods are described: — method A: titration using a burette and starch as indicator; — method B: potentiometric titration with an automatic titrator. The iodine adsorption number is related to the surface area of a carbon black and is generally in agreement with the nitrogen surface area. However, it is significantly depressed in the presence of a high content of volatile or solvent-extractable materials; the iodine adsorption number therefore does not always provide a nwasure of the specific surface area of a carbon black. Ageing of carbon black can also influence the iodine number. In case of dispute, the preferred method is method B (potentiometric titration). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 385, Labo ratory glassware — Burettes ISO 648, Laboratory glassware — Single-volume pipettes…

ISO/IEC 27009-2016 pdf free.Information technology一Security techniques一Sector-specific application of ISO/IEC 27001一 Requirements. ISO/IEC 27009 defines the requirements for the use of ISO/IEC 27001 in any specific sector (field, application area or market sector). It explains how to include requirements additional to those in ISO/IEC 27001, how to refine any of the ISO/IEC 27001 requirements, and how to Include controls or control sets in addition to ISO/IEC 27001:2013, Annex A. This International Standard ensures that additional or refined requirements are not in conflict with the requirements in ISO/IEC 27001. This International Standard Is applicable to those Involved in producing sector-specific standards that relate to ISO/IEC 27001. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 27000:20 16, Information technology — Security techniques — information security management systems — Overview and vocabulary ISO/IEC 27001:2013, information technology — Security techniques — information security management systems Requirements ISO/IEC 27002:2013, Information technology — Security techniques — Code of practice for information security controls 3 Terms and definitions For the…

ISO 9934-1-2016 pdf free.Non-destructive testing一Magnetic particle testing Part 1: General principles. 9.1 Properties and selection of media The characterization of detection media shall he in accordance with ISO 9934-2. Various types of detection media exist in magnetic particle testing. Usually the detection media is a suspension of coloured (including black) or fluorescent magnetic particles in a carrier fluid. Water- based carriers shall contain wetting agents and usually a corrosion inhibitor. Dry powders are also available. They are generally less able to reveal fine surface discontinuities. Fluorescent detection media usually gives the highest sensitivity provided there is an appropriate surface finish. good drainage to maximize indication contrast, and well controlled viewing conditions, in accordance with Clause 10. Coloured detection media can also offer high sensitivity if the contrast with the part surface is sufficient. Black and other colours are available. NOTE To achieve good colour contrast between discontinuities and the test surface, it might be necessary to apply a thin layer of contrast aid paint in accordance with (‘lauj and 10. 9.2 Testing of detection media ISO 9934-2 defines mandatory and recommended tests that are to be carried out before or periodically during inspection. A sensitivity check shall be carried out…

ISO 7199-2016 pdf free.Cardiovascular implants and artificial organs一Blood gas exchangers (oxygenators) This document specifies requirements for sterile, single-use, extracorporeal blood-gas exchangers (oxygenators) intended for supply of oxygen to, and removal of carbon dioxide from, the blood of humans. This document also applies to heat exchangers and arterial filters that are integral parts of the oxygenator. This document also applies to external equipment unique to the use of the oxygenator. This document does not apply to — implanted oxygenators, — liquid oxygenators, — extracorporeal circuits (blood tubing), — separate heat exchangers, — separate ancillary devices, and — separate arterial line filter. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10993-1, Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk management process ISO 10993-4, Biological evaluation of medical devices — Part 4: Selection of tests for interaction with blood 150 10993-7, Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals ISO…

ISO 4499-4-2016 pdf free.Hardmetals一Metallographic determination of microstructure – Part 4: Characterisation of porosity, carbon defects and eta-phase content. This part of ISO 4499 handles the following key issues: — description of methods for sample preparation; — description of how to identify and measure the relevant feature. In some cases, the approach adopted in ISO 4499-2 and ISO 4499-3 can be useful, whereby the intercept method is used on microphotographs of the structure for relevant quantification of feature size, such as eta-phase or graphite rosettes. 6 Apparatus 6.1 Metallographic optical microscope, or other suitable equipment permitting observations and measurements on a screen up to the required magnification. 6.2 Scanning electron microscope (SEM), permitting observations and measurements of features too small to be resolved with an optical microscope. 6.3 Equipment for preparation of test-piece sections. 7 Calibration of measurement apparatus For reliable quantitative measurements, images shall be calibrated against a stage micrometre or scale traceable to a National Reference Standard. The most commonly used stage micrometres for SEMs are the SIRA grids. These are ruled lines which form a grid and are available with 19,7 lines/mm and 2 160 lines/mm. However, these shall also be calibrated and certified as being traceable to…

ISO 27668-1-2016 pdf free.Gel ink ball pens and refills一Part 1: General use. This part of Iso 27668 establishes minimum quality requirements for gel ink ball pens (refillable and non-refillable) and refills for general use. Additional requirements for gel ink ball pens for documentary use are given in ISO 27668-2. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1O5-A02, Textiles — Tests for colourfastness — Part A02: Grey scale for assessing change in colour ISO 105-B02, Textiles — Tests for colourfastness — Part B02: Colourfastness to artificial light: Xenon arc fading lamp test ISO 534, Paper and board — Determination of thickness, density and specific volume ISO 535, Paper and board — Determination of water absorptiveness — Cobb method ISO 536, Paper and board — Determination ofgrammage ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) ISO 2144, Paper, board and pulps — Determination of residue (ash) on ignition at 900 degrees C ISO 5627,…

BS EN ISO 105-G01:2016 pdf free.Textiles一1 Tests for color fastness Part G01: Colours fastness to nitrogen oxide (ISO 105-G01:2016) This part of Iso 105 specifies two methods for determining the resistance of the colour of textiles of all kinds and in all forms to the action of nitrogen oxides produced during combustion of gas, coal, oil. etc., and when air is passed over heated filaments. The two tests differ in severity; one or both of them are used, depending on the result obtained (Z2A). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO I 05-A02, Textiles — Tests for colourfastness — Part A02: Grey scale for assessing change in colour ISO 105- F02, Textiles — Tests for colour fastness — Part F02: Specification for cotton and viscose ad] acent fabrics ISO 139, Textiles — Standard atmospheres for conditioning and testing ISO 3696, Water for analytical laboratory use — Specification and test methods 3 Principle Specimens of textiles are exposed to nitrogen oxides in…