AS 5226.1:2021 pdf free.Cranes –  Anchoring devices for in-service and out-of-service conditions Part 1: General (ISO 12210-1:1998, MOD). This part of ISO 12210 establishes the general criteria for the provision of anchoring devices for cranes and crane parts for in-service and out-of-service conditions. Other parts of ISO 11210 present the requirements for specific crane types. 2 Normative references The following standards contain provisions, which, through reference in this text, constitute provisions of this part of ISO 12210. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties to agreements based on this part of ISO 12210 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of the IEC and ISO maintain registers of currently valid International Standards. ISO 4302:1981, Cranes — Wind load assessment. ISO 8686-1: 1989, Cranes — Design principles for loads and load combinations — Part 1: GeneraL 3 Design requirements Anchoring devices shall withstand the forces applied to them by the crane, taking account of dead and live loads, wind and other environmental factors (see requirements in ISO 4302 and ISO 8686-1). Such devices shall be provided to ensure that…

AS 3584.4:2021 pdf free.Diesel engine systems for underground coal mines Part 4: Emissions. This document specifies the test equipment, test cycles, performance and reporting requirements for type testing of exhaust emissions for diesel engine systems (DES) to be used in underground coal mines. This document applies to— (a) fire-protected DES as defined in AS 3584.1; and (b) explosion-protected DES as defined in AS 3584.2. 1.2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. NOTE Documents referenced for informative purposes are listed in the Bibliography. AS 3584.1, Diesel engine systems for underground coal mines, Part 1: Fire protected — Heavy duty AS 3584.2, Diesel engine systems for underground coal mines, Part 2: Explosion protected AS/NZS 3584.3, Diesel engine systems for underground coal mines, Part 3: Maintenance AS ISO/JEC 17025, General requirements for the competence of testing and calibration laboratories ISO 8178-1, Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test- bed measurement systems of gaseous and particulate emissions ISO 8178-4, Reciprocating internal combustion engines — Exhaust emission measurement — Part 4: Steady-state and transient test cycles for different engine…

AS 2758.2:2021 pdf free.Aggregates and rock for engineering purposes Part 2: Specification for sealing aggregate. This document provides a basis for specifying requirements for aggregates intended for use in sprayed bituminous surfacing. The requirements relate to quality of rock and other properties of coarse aggregate. A coarse aggregate may be produced from rock, gravel, metallurgical slag or suitable synthetic materials. This document is intended for use by — (a) federal, state and local government authorities (whether or not they are specifiers); (b) consultant engineers (whether specifiers or not); (c) suppliers and purchasers of asphalt aggregates; (d) testing authorities; (e) quality system certifiers and accreditation authorities; and (f) educational organisations. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. NOTE Documents referenced for informative purposes are listed in the Bibliography. AS 1141.3.1, Met hods for sampling and testing aggregates, Method 3.1: Sampling—Aggregates AS 1141.11.1, Methods for sampling and testing aggregates, Method 11.1: Particle size distribution — Sieving method AS 1141.11.2, Methods for sampling and testing aggregates, Method 11.2: Particle size distribution for vision sizing systems AS 1141.14, Met hodsforsampling and testing aggregates,…

AS 2671:2021 pdf free.Hydraulic fluid power一General rules and safety requirements for systems and their components (ISO 4413:2010, MOD). AS 2671 specifies general rules and safety requirements for hydraulic fluid power systems and components used on machinery as defined by ISO 12100:2010, 3.1. It deals with all significant hazards associated with hydraulic fluid power systems and specifies the principles to apply in order to avoid those hazards when the systems are put to their intended use. NOTE 1 See Clause 4 and Annex A. The significant hazard noise is incompletely dealt with in this International Standard. NOTE 2 Noise emission depends especially on the installation of hydraulic components or systems into machinery. This International Standard applies to the design, construction and modification of systems and their components, also taking into account the following aspects: a) assembly; b) installation; c) adjustment; d) uninterrupted system operation; e) ease and economy of maintenance and cleaning; f) reliable operation in all intended uses; g) energy efficiency; and h) environment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)…

AS ISO 6015:2021 pdf free.Earth-moving machinery一Hydraulic excavators and backhoe loaders – Methods of determining tool forces. AS ISO 6015 specifies methods for measuring and calculating the tool forces of earth- moving attachments fitted to hydraulic excavators and the hoe equipment of backhoe loaders. It is applicable to hydraulic excavators and backhoe loaders as defined in Iso 6165. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 60 16:1998, Earth-moving machinery — Methods of measuring the masses of whole machines, their equipment and components ISO 6165, Earth-moving machinery — Basic types — ldentqication and terms and definitions ISO 6746-1:2003, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 7135:1993, Earth-moving machinery — Hydraulic excavators — Terminology and commercial specifications ISO 7451:1997, Earth-moving machinery — Volumetric ratings for hyd raulic excavator buckets and backhoe loader buckets ISO 7546:1983, Earth-moving machinery — Loader and front loading excavator buckets — Volumetric ratings ISO 9248:1992, Earth-moving machinery — Units for dimensions, performance and capacities, and their measurement accuracies 3 Terms and…

AS 12508:2021 pdf free.Earth-moving machinery一Operator station and maintenance areas – – Bluntness of edges (ISO 12508:1994, MOD). AS 12508 defines the permissible limits of the sharpness of edges and corners, to reduce the risk of injury to the operator or maintenance personnel while operating earth-moving machinery and performing maintenance. It applies to operator and maintenance access/egress systems as defined in ISO 2860 and ISO 2867, and the operator station on earth-moving machinery as described in ISO 6165. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 2860:1992, Earth-moving machinery — Minimum access dimensions. ISO 2867: 1994, Earth-moving machinery —Access systems. ISO 6165:1987, Earth-moving machinery — Basic types — Vocabulary. 3 Requirements Structural edges and corners (see figure 1) of metallic and non-metallic materials of sufficient hardness to cause contusions or penetration of the human…

AS ISO 22915.21:2021 pdf free.Industrial trucks一Verification of stability Part 21: Order-picking trucks with operator position elevating above 1 200 mm. This document specifies the tests for verifying the stability of order picking trucks with an elevating operator position, as defined in ISO 5053-1. where the operator’s position can be raised to an elevation above 1 200 mm. It is applicable to industrial trucks fitted with fork arms, platforms and/or integrated attachments under normal operating conditions. It is not applicable to trucks fitted with a load carrier that can be shifted laterally or pivoted out of the truck’s longitudinal centre plane. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5053-1, industrial trucks — Terminology and classification — Part 1: Types of industrial trucks ISO 22915-1, Industrial trucks — Verification of stability — Part 1: General 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5053-1 and ISO 22915-1 and the…

AS 61869.3:2021 pdf free.Instrument transformers Part 3: Additional requirements for inductive voltage transformers (IEC 61869-3:2011 (ED.1.0) MOD). This part of IEC 61869 applies to new inductive voltage transformers for use with electrical measuring instruments and electrical protective devices at frequencies from 15 Hz to 100 Hz. NOTE 301 Requirements specific to three-phase voltage transformers are not Included In this standard but. so tar as they are relevant, the requirements in clauses 4 to 10 apply to these Iransformers and a few references to them are included in those clauses (e.g. see 3.1.303, 5.301.1, 5.301.2. 5.5.301, 6.13.301.1 and Table 304). All the transformers shall be suitable for measuring purposes, but, in addition, certain types may be suitable for protection purposes. Transformers for the dual purpose of measurement and protection shall comply with all clauses of this standard. 2 Normative references Clause 2 of IEC 61869-1:2007 is applicable with the following additions: IEC 60028. International Standard of resistance for copper IEC 60038, IEC standard voltages IEC 61869-1:2007, Instrument transformers — Part 1: General requirements 3 Terms, definitions and abbreviations For the purposes of this document, the terms and definitions in IEC 61869-1:2007 apply with the following additions: 3.1 General definitions 3.1.30 1…

AS ISO 8813:2021 pdf free.Earth-moving machinery一Lift capacity of pipelayers and wheeled tractors or loaders equipped with side boom. AS ISO 8813 provides a uniform method of calculating, and a test method for validating, rated lift capacity as presented in commercial literature for pipelayers and wheeled tractors or loaders equipped with a vertical-only pivoted, hydraulic or mechanically operated, side boom. The rated lift capacity considers hoist mechanism limits, tipping loads and rope factor. After the lift capacity has been calculated and validated, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or wheeled machine configuration. This International Standard applies to machines having a lift capacity greater than 10 000 N when used in lifting applications. It includes pipelayers as defined in ISO 6165 and ISO 7136, and wheeled tractors and loaders as defined in ISO 6165, ISO 6747 and ISO 7131. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the…

AS/NZS IEC 60331.2:2021 pdf free.Tests for electric cables under fire conditions一Circuit integrity. This part of IEC 60331 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 v/i 000 V, including those of rated voltage below 80 V, metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables of not greater than 20 mm overall diameter. Cables of larger diameter are intended to be tested using the apparatus, procedure and requirements of IEC 60331-i. This document includes details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 viiooo V. Details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-2. Although the scope is restricted to cables with rated voltage up to and including 0,6/1,0 kV, the procedure can be used, with the…