BS ISO 6361-3:2014 pdf download.Wrought aluminium and aluminium alloys – Sheets, strips and plates Part 3: Strips: Tolerances on shape and dimensions. This part of Iso 6361 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy strip by cold-rolling for general engineering applications. It applies to products with thickness of over 0,15 mm up to, and including 16 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock), or to special products such as those that are corrugated or embossed. Technical conditions for inspection and delivery of products covered by this part of ISO 6361 are specified in ISO 6361-1. 2 Dimensional tolerances 2.1 Thickness Thickness tolerances shall be in accordance with Tablcsj. and 2. When the tolerance is specified as either all plus, or minus side, the value in TableI or in Tablel shall be doubled. Tolerances for the products exceeding the range of specified thickness and width shall be agreed upon by the purchaser and the supplier.BS ISO 6361-3 pdf download.

ISO 1797-1-2011 pdf free. Dentistry一Shanks for rotary instruments – Part 1: Shanks made of metals. This International Standard specifies shanks for rotary instruments used in dentistry and gives measurement methods for the venfication of dimensions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1942, Dentistry — Vocabulary ISO 3274, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments ISO 4288, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and procedures for the assessment of surface texture ISO 6507-1 • Metallic materials — Vickers hardness test — Part 1: Test method ISO 8325, Dentistry — Test methods for rotary instruments 3 Terms, definitions, symbols and abbreviated terms 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1942 and the following apply. 3.1.1 shank part of a rotary instrument used in dentistry which is designed to fit into the chuck of a straight or geared dental handpiece, a technical handpiece or a dental turbine…

ISO 10360-7-2011 pdf download.Geometrical product specifications (GPS)- Acceptance and reverification tests for coordinate measuring machines (CMM) – Part 7: CMMs equipped with imaging probing systems. This part of ISO 10360 specifies the acceptance tests for verifying the performance of a coordinate measuring machine (CMM) used for measuring linear dimensions as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the CMM. The acceptance and reverification tests given in this part of ISO 10360 are applicable only to Cartesian CMMs using imaging probing systems of any type operating in the discrete-point probing mode. This part of ISO 10360 does not explicitly apply to: — non-Cartesian CMMs: however, parties may apply this part of ISO 10360 to non-Cartesian CMMs by mutual agreement; — CMMs using other types of optical probing: however, parties may apply this approach to other optical CMMs by mutual agreement; — CMMs using contact probing systems (see ISO 10360-2 for contact probing systems). This part of ISO 10360 specifies performance requirements that can be assigned by the manufacturer or the user of a CMM, the manner of execution of the acceptance and reverification tests to demonstrate the stated…

ISO 13503-1-2011 pdf download.Petroleum and natural gas industries – Completion fluids and materials – Part 1: Measurement of viscous properties of completion fluids. 3 Measurement and precision Temperatures shall be measured to an accuracy of ±1 °C (±2 °F); pH shall be measured to an accuracy of ±0,1 units. All other quantitative measurements shall be made to an accuracy of ±2 %, unless specified otherwise. 4 Fluid preparation Certain aspects of sample preparation and handling can affect the viscosity or rheological properties of a fluid. During all procedures, steps shall be taken to minimize entraining air into the fluid. The procedure used to prepare the fluid sample shall be documented, including the following information: a) description and/or composition of the base fluid; preparation of the fluid shall be described, starting with the fluid source, such as deionized water, tap water, completion brines, produced water, seawater or type of oil: b) identification of mixing apparatus, container volume, and total volume of fluid prepared; C) identification of each fluid component and amount added; d) the order and method of addition of each component; e) mixing speeds, with time at each speed; f) ageing or holding time prior to measurements, if required; g)…

ISO 13385-2-2011 pdf download.Geometrical product specifications (GPS)一Dimensional measuring equipment – Part 2: Calliper depth gauges; Design and metrological characteristics. This part of ISO 13385 provides the most important design and metrological characteristics of calliper depth gauges: — with analogue indication: vernier scale or circular scale (dial), and — with digital indication: digital display. 2 Normative references The following referenced documents are indispensable for the application of this öocument. ror daeo references, only the cited editions apply. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 14253-1, Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for proving conformance or non-conformance With specifications ISO 14253-2:2011. Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification ISO 14978:2006, Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment IEC 60529, Degrees of protection by enclosures (IP Code) ISOIIEC Guide 98-3. Uncerlaioty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM: 1995) ISO/IEC Guide 99, International…

ISO 6721-11-2012 pdf free.Plastics – Determination of dynamic mechanical properties – Part 11: Glass transition temperature. This part of ISO 6721 specifies methods for determining a value of the glass transition temperature (T9) from the dynamic mechanical properties measured during a linear temperature scan under heating conditions. The glass transition temperature is an indicator of the transition from a glassy state to a rubbery state. Usually referred to as dynamic mechanical analysis (DMA), the methods and their associated procedures can be applied to unreinforced and filled polymers, foams, rubbers, adhesives and fibre-reinforced plastics/composites. Different modes (e.g. flexure, compression, tension) of dynamic mechanical analysis can be applied, as appropriate, to the form of the source material. NOTE For tests undertaken in the flexure or torsion mode, an additional procedure is included to identify the severity of the influences of thermal lag on the measured data (see Annex B). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6721-1:2011, Plastics — Determination of dynamic mechanical properties — Part 1: General principles 3 Terms…

ISO 36-2011 pdf download.Rubber, vulcanized or thermoplastic – Determination of adhesion to textile fabrics. ISO 36 specifies a method of test for measuring the force required to separate, by stripping, two plies of fabric bonded with rubber, or a rubber layer and a fabric ply bonded together, The method is applicable when the ply surfaces are approximately plane or when they are in the form of a cylinder having an internal diameter greater than approximately 50 mm. The method is not applicable when the ply surfaces contain sharp bends, angles or other gross irregularities which cannot be excluded when cutting out test pieces. This International Standard does not apply to coated fabrics, which are tested in accordance with ISO 2411, Rubber- or plastics-coated fabrics — Determination of coating adhesion, or textile conveyor belts, which are tested in accordance with ISO 252. Conveyor belts — Adhesion between constitutive elements — Test methods. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5893:2002, Rubber and plastics test equipment — Tensile, flexural and compression…

ISO 1518-1-2011 pdf download.Paints and varnishes – Determination of scratch resistance 一 Part 1: Constant-loading method. This part of ISO 1518 specifies a test method for determining under defined conditions the resistance of a single coating o a multi-coat system of paint, varnish or related product to penetration by scratching with a scratch stylus loaded with a specified load. Penetration of the stylus is to the substrate, except in the case of a multi-coat system, in which case the stylus can penetrate either to the substrate or to an intermediate coat. The method specified can be carried out a) either as a pass/fail” test, by testing with a single specified load applied to the stylus to assess compliance with a particular specification; b) or by applying increasing loads to the stylus to determine the minimum load at which the coating is penetrated. 2 Normative references The following referenced documents are indispensable foi the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1513, Paints and varnishes — Examination and preparation of test samples ISO 1514, Paints and varnishes — Standard panels for…

ISO 15-2011 pdf free download.Rolling bearings一Radial bearings一 Boundary dimensions, general plan. ISO 15 specifies preferred boundary dimensions for radial bearings of the diameter series 7, 8, 9, 0, 1, 2, 3 and 4. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 464, Rolling bearings — Radial bearings with locating snap ring — Dimensions and tolerances ISO 582, Rolling bearings — Chamfer dimensions — Maximum values ISO 5593, Rolling bearings — Vocabulary ISO 12043, Rolling bearings — Single-row cylindrical roller bearings — Chamfer dimensions for loose rib and non-nb sides ISO 12044, Rolling bearings — Single-row angular contact ball bearings — Chamfer dimensions for outer ring non-thrust side ISO 15241, Rolling bearings — Symbols for quantities 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5593 apply. 4 Symbols For the purposes of this document, the symbols given in ISO 15241 and the following apply. The symbols shown in Figure 1 and given in Tables 1 to 8 denote nominal dimensions, unless specified…

ISO 7380-1-2011 pdf free.Button head screws – Part 1: Hexagon socket button head screws. ISO 7380-1 specifies the characteristics of hexagon socket button head screws with threads from M3 up to and including M16, with product grade A and with reduced loadability according to Table 3. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, e.g. ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 3506-1 and ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions ISO 261, ISO general purpose metric screw threads — General plan ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread ISO 965-2, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw…