BS ISO 8637-3:2018 pdf free.Extracorporeal systems for blood purification Part 3: Plasmafilters. The performance characteristics specified in 4.3 shall be determined prior to marketing a new type of device and shall be re-evaluated after changes in the device that might alter its performance. The sample of device shall be drawn at random from the manufacturer’s production and shall have passed all applicable quality control steps, as well as sterilization. They shall be prepared according to the manufacturer’s recommendations as though they are to be used for a clinical procedure Measurements shall be made in vitro at (37 ± 1) °C. When the relationship between variables is nonlinear, sufficient determinations shall be made to permit interpolation between the data points. The techniques of measurement given in this document are reference tests. Other test methods may be used, provided they have been validated and shown to be precise and reproducible. The test systems shown do not indicate all the necessary details of practicable test apparatus. The design and construction of actual test systems and the establishment of actual test systems shall also address the many factors contributing to measurement error, including, but not limited to, pressure measurement errors due to static head…

ISO 16837-2019 pdf free.Non-destructive testing一Acoustic emission testing- Test method for damage qualification of reinforced concrete beams. The internal noise of the amplifier shall be inherently low and less than 20 1.tV (26 dBAE for 0 dBAE = 1 iV) as the peak voltage converted by input voltage. The amplifier shall be also robust enough against the environmental conditions and be protected properly. The frequency range shall be determined prior to the measurement, taking into account the performance of AE sensor and the amplifiers. A suggested range in concrete is from around 10 kFIz to 100 kHz, because such higher frequency components as over 1 MHz readily attenuate in concrete. For signal analysis, AE parameters of AE count or AE hit shall be detected and processed. The measurement system shall be able to obtain time information along with AE data. In addition, such external parameters as load, strain and so forth are preferably recorded in the system, which can be equipped with enough memory to record the data measured. It is preferable that all the data recorded be analyzed digitally by computer. 5 Environmental noises In advance of the AE measurement, the noise level shall be estimated. Then, counteract against external…

ISO 6507-2-2018 pdf free.Metallic materials一Vickers hardness test一 Part 2: Verification and calibration of testing machines. 5.1.1 Direct verification shall be conducted in accordance with the schedule given in Clausel. 5.1.2 Direct verification involves: a) calibration of the test force; b) verification of the indenter; c) calibration and verification of the diagonal measuring system; d) verification of the testing cycle. 5.1.3 Direct verification should be carried out at a temperature of (23 ± 5) °C. If the verification is made outside this temperature range, this shall be stated in the verification report. 5.1.4 The instruments used for verification and calibration shall be traceable to national standards. 5.2 Calibration of the test force 5.2.1 Each test force used within the working range of the testing machine shall be measured. Whenever the indenter position affects the applied force, this shall be done at not less than three positions of the plunger uniformly spaced throughout its range of movement during testing. For testing machines whose test force is shown not to he influenced by the position of the plunger, e.g. closed-loop controlled loading system, the test force can be calibrated in one position. 5.2.2 The test force shall be measured by one of the…

ISO 247-2-2018 pdf free.Rubber- Determination of ash – Part 2: Thermogravimetric analysis (TGA). 6.1 Thermogravlmetric analyser. comprising the following elements: a) Therino-balance; b) Heating furnace; c) Temperature programmer; d) Gas flow controller, for controlling the purge gas to the balance and furnace, and keeping a constant flow rate. 6.2 Sample pan. platinum pan or alumina ceramic pan. 6.3 Analytical balance, capable of weighing to the nearest 0,1 mg. 7 Preparation of the test sample 7.1 For raw natural rubber, test samples shall be cut from the homogenized piece prepared in accordance with ISO 1795. For raw synthetic rubber, test samples shall be cut from the dried rubber obtained after carrying out the determination of volatile-matter content in accordance with the hot-mill method of ISO 248-1. Take a test portion of about 2 g to 5 g from the homogenized sample and cut into pieces by hand. 7.2 Test samples of rubber compounds shall be sheeted on a mill and cut into pieces by hand. 7.3 Test samples of vulcanizates shall be sheeted or crumbed on a mill or comminuted by hand. 7.4 Care shall be taken to ensure that test samples of rubber compounds and vulcanizates are representative of the…

ISO 7599-2018 pdf free.Anodizing of aluminium and its alloys一Method for specifying decorative and protective anodic oxidation coatings on aluminium. The information required from the customer by the anodizer in order to anodize the product correctly is given in 42 and 4: 42 specifies information that is essential whenever a product is to be anodized; 4,3 identifies additional information required for particular product applications. A summary of the subclause references relating to this information is given in Annex F. NOTE Certain properties (for example, high specular reflectance) are only obtainable by the use of special alloys, and some properties can be incompatible with others. The customer and the anodizer can share the information about cleaning in case of external architectural application (see Annex E). 4.2 Essential information The following information shall be supplied by the customer to the anodizer, if necessary in consultation with the aluminium supplier and/or anodizer: a) a reference to this document, i.e. ISO 7599; b) the intended service use of the article to be anodized; c) the specification of the aluminium to be anodized; d) an indication of the significant surface(s) of the article to be anodized; e) the surface preparation to be used on the aluminium…

ISO 129-5-2018 pdf free.Technical product documentation – Indication of dimensions and tolerances – Part 5: Dimensioning of structural metal work. The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 129-1, Technical drawings — Indication of dimensions and tolerances Part 1: General principles ISO 129-4, Technical product documentation (TPD) — Indication of dimensions and tolerances — Part 4: Dimensioning of shipbuilding drawings ISO 5261:1995, Technical drawings — Simplified representation of bars and profile sections ISO 657-1. Hot-rolled steel sections — Part 1: Equal-leg angles — Dimensions ISO 657-2, Hot-rolled steel sections — Part 2: Unequal-leg angles — Dimensions ISO 657-16, Hot-rolled steel sections — Part 16: Sloping flange column sections (metric series) — Dimensions and sectional properties ISO 657-18, Hot-rolled steel sections — Part 18: L sections for shipbuilding (metric series) Dimensions, sectional properties and tolerances ISO 657-21, Hot-rolled steel sections — Part 21: T-sections with equal depth and flange width — Dimensions ISO 10209, Technical product documentation — Vocabulary — Terms…

BS EN ISO 20184-1:2018 pdf free.Molecular in vitro diagnostic examinations – Specifications for pre-examination processes for frozen tissue Part 1: Isolated RNA. For general statements on medical laboratory quality management systems and in particular on specimen collection, reception and handling (including avoidance of cross contaminations) see ISO 15189:2012, 4.2, 5.4.4, 5.4.6 or ISO/IEC 17020:2012， Clause 8 and 7.2. The requirements on laboratory equipment, reagents, and consumables in accordance with ISO 15189:2012, 5.3 shall be followed; ISO 15189:2012, 5.5.1.2 and 5.5.1.3, and ISO/IEC 17020:2012, 6.2 can also apply. All steps of a diagnostic workilow can influence the final analytical test result. Thus, the entire workf low including biomolecule stability and sample storage conditions shall be verified and validated. Workflow steps which cannot always be controlled (e.g. warm ischemia) shall be documented. A risk assessment of non-controllable workflow steps including their potential impact on the analytical test performance shall be performed and mitigation measures shall be established to enable the required analytical test performance. Before or during the design of an analytical test, it should therefore be investigated and assured that the RNA profile(s) intended to be analysed is/are not compromised in a manner impacting the analytical test performance (e.g. by performing…

ISO 10003-2018 pdf free.Quality management一Customer satisfaction一Guidelines for dispute resol lution external to organizations Management de la qualite一Satisfaction du client一Lignes directrices relatives a la resolution externe de conflits aux organismes. association <customer satisfaction> organization (3.J.2) consisting of member organizations or persons [SOURCE: 150 9000:2015, 3.2.8] 3.2 complainant person, organization (3112) or their representative, making a complaint (3.3) Note I to entry: In this document, customers (34) who refer their complaints to a provider in the first instance are also considered to be ‘compIainants.[SOURCE: ISO 10001:2018, 3.2, modified — Note Ito entry has been added.] 3.3 complaint <customer satisfaction> expression of dissatisfaction made to an organization (3.12). related to its product or service, or the complaints-handling process itself, where a response or resolution is explicitly or implicitly expected Note ito entry: Complaints can be made in relation to other processes where the organization interacts with the customer (14). Note 2 to entry: Complaints can be made directly or indirectly to the organization.[SOURCE: 150 9000:2015, 3.9.3, modified — Notes 1 and 2 to entry have been added.1 3.4 customer person or organization (3.12) that could or does receive a product or a service that is intended for or required by this person or…

ISO 8504-3-2018 pdf free.Preparation of steel substrates before application of paints and related products – Surface preparation methods – Part 3: Hand- and power-tool cleaning. The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8501-1, Preparation of steel substrates before application of paints and related products — Visual assess ment ofsurjàce cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatin,qs ISO 8501-2, Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https://www.iso.org/obp — IEC Electropedia: available at http://www.electropedia.orgj 3.1 hand-tool cleaning method of preparing steel substrates…

ISO 8307-2018 pdf free.Flexible cellular polymeric materials – Determination of resilience by ball rebound. 6.1 The test pieces shall have plane, parallel top and bottom surfaces. 6.2 The test pieces shall consist of the entire product sample or a suitable portion of it, except that in no case shall the thickness be less than 50 mm or the area less than 100 mm x 100 mm. Test pieces less than 50 mm thick shall be plied up. without the use of cement, to a minimum of 50 mm. For moulded products, the top skin shall be removed. Thicker test pieces can be used to avoid spurious results, which can occur with very soft materials due to the influence of the baseplate. NOTE The minimum test piece thickness of 50 mm cannot be sufficient for very soft materials: if spurious results are obtained, a thicker test piece can be used. Very low density materials can also cause problems due to rebound of the test piece itself. With multiple-ply test pieces, slipping can occur between the plies. This problem can be overcome by using the largest possible area of the test piece. 7 Number of test pieces Three test pieces per sample…