BS ISO 8036:2015 pdf free.Microscopes一Immersion liquids for light microscopy. BS ISO 8036 describes the characteristics of immersion liquids used in microscopy. It classifies immersion liquids according to their field of application and specifies requirements and test methods for each type. This International Standard further specifies a system of designation for immersion liquids, the information to be included on container labels, and the information to be supplied in technical data sheets. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2592, Determination offlash and fire points — Cleveland open cup method ISO 8255-1, Microscopes — Cover glasses — Part 1: Dimensionaltolerances, thickness and optical properties ISO 8255-2, Microscopes — Cover glasses — Part 2: Quality of materials, standards of finish and mode of packaging 3 Classification Depending on their field of application, immersion liquids are classified as follows: — type N: immersion oil for general use in light microscopy; — type F: immersion oil which meets the requirements of fluorescence microscopy; — type G:…

BS ISO 7509:2015 pdf free.Plastics piping systems一 Glass-reinforced thermosetting plastics (GRP) pipes一 Determination of time to failure under sustained internal pressure. BS ISO 7509 specifies a method for determining the time-to-failure of glass-reinforced thermosetting plastics (GRP) pipes under internal hydrostatic pressure at a specified temperature. The external environment can be air or water. NOTE Forotherinternal orexternal environments, the referringstandard is to specifyanyadditional requirement. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions ISO 10928, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 failure occurrence of bursting, leaking, or weeping Note ito entry: See 2.1. 3.2 bursting failure by rupture of the pipe wall with immediate loss of test liquid and drop of pressure Note ito entry: See 9.1. and 92.1.. 3.3 leaking failure by…

BS ISO 7504:2015 pdf free.Gas analysis一Vocabulary. BS ISO 7504 defines terms related to gas analysis, with the main locus on terms related to calibration gas mixtures for use in gas analysis and gas measurements. It does not cover terms which relate only to specific applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC Guide 98-3:2008, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) lSO/IEC Guide 99:2007, International vocabulary of metrology — Basic and general concepts and associated terms (ViM) ISO 10715:1997, Natural gas — Sampling guidelines 3 Terms relating to general concepts Terms used in the field of gas analysis that are well defined by either ISO/IEC Guide 98-3 or ISO/IEC Guide 99 are included in Annex A. 3.1 homogeneity state of a gas mixture wherein all of its components (13) are distributed uniformly throughout the volume occupied by the gas mixture 3.2 stability attribute of a gas mixture, under specified conditions, to maintain its…

BS ISO 6953-1:2015 pdf free.Pneumatic fluid power – Compressed air pressure regulators and filter-regulators Part 1: Main characteristics to be included in literature from suppliers and product- marking requirements. This part of Iso 6953 specifies which characteristics of compressed air pressure regulators are to be included in literature from their suppliers. It also applies to filter-regulators. This part of ISO 6953 applies to — manually controlled direct operated types (with or without relieving mechanism), — manually controlled internal pilot operating types (e.g. nozzle flapper), and — external pilot operated types. In addition, it specifies the product marking requirements for pressure regulators and filter-regulators. This part of ISO 6953 is applicable to compressed air pressure regulators with a rated inlet pressure of up to 2 500 kPa (25 bar) and an outlet adjustment pressure of up to 1 600 kPa (16 bar); and to filter-regulators with rated inlet and outlet pressures of up to 1 600 kPa (16 bar), in which the major contaminants are removed by mechanical means. NOTE I I bar = 0,1 MPa = 105 Pa; I MPa = I N/mmZ. The rated pressure should be selected from the preferred pressures listed in ISO 2944. NOTE 2 The…

BS ISO 6469-4:2015 pdf free.Electrically propelled road vehicles一Safety specifications Part 4: Post crash electrical safety. This part of ISO 6469 specifies safety requirements for the electric propulsion systems and conductively connected auxiliary electric systems of electrically propelled road vehicles for the protection of persons inside and outside the vehicle. It specifies electrical safety requirements for vehicle post-crash conditions. It applies to electrically propelled road vehicles with voltage class B electric circuits. It does not apply to motorcycles and mopeds. It does not specify any crash test procedure. The safety requirements of this part of ISO 6469 apply to applicable vehicles in accordance with published crash test procedures of each country or region. Applicable vehicles are those vehicles which are explicitly specified in these crash test procedures. It does not provide comprehensive safety information for first responders, emergency services, maintenance, and repair personnel. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6469-3, Electrically propelled road vehicles — Safety specifications — Part 3: Protection…

BS ISO 6432:2015 pdf free.Pneumatic fluid power一 Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8mmto25mm一Basicand mounting dimensions. BS ISO 6432 establishes a metric series of mounting dimensions required for interchangeability of commonly used pneumatic cylinders for a maximum working pressure of 1 000 kPa (10 bar). NOTF This International Standard allows manufacturers freedom of design in metric cylinders and does not restrict technical development but provides basic guidelines. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3320, Fluid power systems and components — Cylinder bores and piston rod diameters and area ratios — Metric series ISO 4393, Fluid power systems and components — Cylinders — Basic series of piston strokes ISO 4395, Fluid power systems and components — Cylinder piston rod end types and dimensions ISO 5598, Fluid power systems and components — Vocabulary ISO 6099, Fluid power systems and components — Cylinders — Identification code for mounting dimensions and mounting types ISO 16030, Pneumatic fluid power —…

ISO/DIS 6182-14-2015 pdf free.Fire protection – Automatic nozzle systems – Part 1X: Requirements and test methods for water spray nozzles. This part of ISO 6182 specifies performance requirements, methods of test, and marking requirements for open water spray nozzles. This standard does not cover open sprinklers or open water mist nozzles. Factors of installation such as nozzle spacing, design densities, wind and hot gas velocities are not intended to be addressed by this product standard 2 Normative References The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 6182. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 6182 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of lEG and ISO maintain registers of currently valid International Standards. ASTM G36 Standard Practice for Evaluating Stress-Corrosion-Cracking Resistance of Metals and Alloys in a Boiling Magnesium Chloride Solution ISO 7-1:1982 Pipe threads where pressure-tight joints are made on the threads – Part 1: Designation, Dimension and Tolerances ISO 49:1983 Malleable cast iron fittings threaded to ISO 7-1…

E DIN ISO 48:2015 pdf free.Elastomere oder thermoplastische Elastomere – Bestimmung der Harte (Harte zwischen 10 IRHD und 100 IRHD). Das verwendete Prifgerat muss im Wesentlichen den in 5.2 beschriebenen entsprechen, jedoch in den folgenden Punkten abweichen. 5.3.1 Zylindrishe Oberflichen mit cinem Radius uber 50 mm Die Grundplatte des Prifgerates muss unterhalb der Druckstange eine Bohrung fur die freie Durchfuhrung der ringformigen Druckplatte besitzen, so dass Messungen ober- und unterhalb der Grundplatte gemacht werden konnen. Die untere Flache der Grundplatte muss die Form zweier Zylinder aufweisen, die parallel zueinander und zur Ebene der Grundplatte angeordnet sind. Die Durchmesser der Zylinder und ihr gegenseitiger Abstand missen das Aufstellen und den Stand des Priufgerates auf der gekrimmten und zu prifenden Oberflache ermoglichen. Alternativ darf die abgeanderte Grundplatte mit in Kugelgelenken beweglichen FuBen ausgestattet werden, so dass diese sich selbst an die gekrimmte Oberflache anpassen. 532 Oberfbichen mit dopelter Krummung und einem groBen krummungsradius uber 50mm Es ist das in 5.3.1 festgelegte Prufgerat mit verstellbaren FuBen zu verwenden. 5.33 Zylindrische Oberflachen mit einem Radius 4 mm bis 50 mm oder kleine Probckorper mit doppelter Krimmung Bei Oberflachen, die zu klein sind, um als Auflage fur das Prifgerat zu dienen, sind der Probekorper oder…

ISO 8600-2-2015 pdf free.Endoscopes – Medical endoscopes and endotherapy devices – Part 2: Particular requirements for rigid bronchoscopes. This part of Iso 8600 specifies requirements for rigid bronchoscopes and their endoscopic accessories used in the practice of anaesthesia and medical endoscopy. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5356-1:1996, Anaesthetic and respiratory equipment — Conical connectors — Part 1: Cones and sockets ISO 8600-1:2013, Endoscopes — Medical endoscopes and endotherapy devices — Part 1: General requirements 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 8600-1 and the following apply. rigid bronchoscope open straight tube-type rigid endoscope fitted with a means of illumination through the distal end and intended to be introduced into the tracheobronchial airway, having an internal lumen sufficiently large to permit free respiration of the patient 3.2 rigid ventilation bronchoscope rigid bronchoscope, fitted with a removable end-cap at the proximal end of the open straight tube and having an internal…

ISO 738-2015 pdf free.Coniferous sawn timber- Sizes – Permissible deviations and shrinkage. ISO 738 specifies permissible deviations, due to inaccuracies in sawing, from nominal thicknesses, widths and lengths, for coniferous sawn timber. It also gives, for information, average values for shrinkage for some wood species. It is applicable to unplanned square-edged and unedged coniferous sawn timber having thicknesses or widths in the rangelO mm to 310 mm. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 24294, Timber — Round and sawn timber — Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 24294 apply. 4 Permissible deviations and shrinkage The nominal sizes of coniferous sawn timber are established at an absolute moisture content of 20%. NOTE The absolute moisture content is the moisture content related to the oven-dry mass of the timber, expressed as a percentage. The actual thickness and width of sawn timber having moisture contents greater than 20 % may be…