ISO 13007-2-2013 pdf free.Ceramic tiles – Grouts and adhesives – Part 2: Test methods for adhesives.
This part of Iso 13007 describes the methods for determining the characteristics for adhesives used in
the installation of ceramic tiles. The following test methods are described:
— determination of open time (41);
— determination of slip (42);
— determination of shear adhesion strength (4);
— determination of tensile adhesion strength (4A);
— determination of transverse deformation (45).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 13006, Ceramic tiles — Definitions, classification, characteristics and marking
ISO 13007-1, Ceramic tiles — Grouts and adhesives — Part 1: Terms, definitions and specifications for adhesives
3 General test conditions and procedures
3.1 Sampling
A representative sample of at least 2 kg shall be used.
3.2 Test conditions
Standard conditions shall be (23 ± 2) °C and (50 ± 5) % relative humidity and the speed of air in the testing area shall be less than 0,2 m/s. Other test conditions may be specified in Clause 4. The tolerance in the time of conditioning for all test specimens shall be as shown in Table 1 below.
3.3 Test materials
Condition all test materials, including water, for at least 24 h under standard conditions. The adhesive to be tested shall be within its shelf life, where this is specified.
3.3.1 Ceramic tiles
The tiles shall be checked prior to conditioning to ensure that they are unused, clean, and dry. The type of tile shall be as specified under the specific test procedures found in Clause 4.
3.4 Mixing procedures
3.4.1 Cementitious adhesives (C)
The amount of water and/or liquid admix required for preparing the adhesive shall be as stated by the manufacturer in parts by weight, i.e. liquid to dry powder (in cases where a range of values is given, the average shall be used).
Using a minimum quantity of 2 kg of the powder and the recommended quantity of liquid, prepare the adhesive in a planetary mixer using the following slow speed settings: (140 ± 5) rotations per minute and (62 ± 5) rotations per minute planetary movement. See Figures 1 and 2.
Carry out the following procedure.
1) Pour the liquid into the pan.
2) Scatter the dry powder over the liquid.
3) Mixfor30s.
4) Take out the mixing paddle.
5) Scrape down the paddle and pan within 1 mm.
6) Replace the paddle and mix for 1 mm.
If required by the adhesive manufacturer’s instructions, let the adhesive mature as specified and then mix for an additional 15 s.ISO 13007-2 pdf free download.
Tags: Ceramic tiles
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…