ISO 15609-5-2011 pdf free.Specification and qualification of welding procedures for metallic materials – Welding procedure specification -Part 5: Resistance welding.
This part of ISO 15609 specifies requirements for the content of welding procedure specifications forresistance spot, seam, butt and projection welding processes. It is necessary to establish the acceptability ofapplying the principles of this part of lSO 15609 to other resistance and related welding processes before anyqualification is undertaken.
NOTE Details of IS0 15609(all parts — for titles, see Foreword) are given in ISO 15607:2003,Annex A.
Variables listed in this part of lSO 15609 are those influencing either weld dimensions (quality), weld nuggetdimension, weld pattern positioning, mechanical properties or geometry of the welded joint.
Normative references
The following referenced documents are indispensable for the application of this document.For datedreferences,only the edition cited applies.For undated references, the latest edition of the referenceddocument (including any amendments) applies.
ISO 669, Resistance welding —Resistance welding equipment —Mechanical and electrical requirements
ISO 4063,Welding and allied processes —Nomenclature of processes and reference numbers
ISO5183 (all parts), Resistance welding equipment —Electrode adaptors, male taper 1:10ISO 5184,Straight resistance spot welding electrodes
ISO 5821,Resistance welding —Spot welding electrode capsISO 5827,Spot welding – Electrode back-ups and clamps
ISO 8205-1, Water-cooled secondary connection cables for resistance welding — Part 1: Dimensions andrequirements for double-conductor connection cables
ISO 8205-2,Water-cooled secondary connection cables for resistance welding — Part 2: Dimensions andrequirements for single-conductor connection cables
ISO 8430(all parts), Resistance spot welding — Electrode holders
4Technical contents of welding procedure specification4.1 General
The welding procedure specification (WPS) shall provide all information required to make a weld. Theminimum information required in a WPs for resistance welding processes is listed in 4.2 to 4.4.
For some applications, it is necessary to supplement the list.All relevant information shall be specified in thewPS.
Tolerance ranges shall be specified.
Examples of the WPs format are shown in Annexes A, B and C; these forms should be modified according toactual practice.
4.2 Product manufacturer
– ldentification of the product manufacturer.-ldentification of the WPs.
– Reference to the welding procedure qualification record (WPQR— see ISO 15614-12 and ISO 15614- 13).
4.3Parent materials
4.3.1Composition
—Designation and type(s) of the material(s) and referenced standard(s).
—In case of coating(s), type, thickness, single or double sided.
4.3.2Dimensions
—Thickness of material(s).ISO 15609-5 pdf free download.
Tags: Specification and qualification of welding procedures for metallic materials
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…