BS ISO 6361-3:2014 pdf download.Wrought aluminium and aluminium alloys – Sheets, strips and plates Part 3: Strips: Tolerances on shape and dimensions. This part of Iso 6361 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy strip by cold-rolling for general engineering applications. It applies to products with thickness of over 0,15 mm up to, and including 16 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock), or to special products such as those that are corrugated or embossed. Technical conditions for inspection and delivery of products covered by this part of ISO 6361 are specified in ISO 6361-1. 2 Dimensional tolerances 2.1 Thickness Thickness tolerances shall be in accordance with Tablcsj. and 2. When the tolerance is specified as either all plus, or minus side, the value in TableI or in Tablel shall be doubled. Tolerances for the products exceeding the range of specified thickness and width shall be agreed upon by the purchaser and the supplier.BS ISO 6361-3 pdf download.

ISO 6362-1-2012 pdf free.Wrought aluminium and aluminium alloys – Extruded rods/bars, tubes and profiles – Part 1: Technical conditions for inspection and delivery. This part of ISO 6362 specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy rods/bars, tubes and profiles for general engineering applications. II applies to extruded products, but does not apply to the following: — forging stock; — extruded precision profiles in alloys A6060 and A6063; — products delivered in coils; — coiled tubes cut to lengths. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6362-2, Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 2: Mechanical properties ISO 6362-3, Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 3: Extruded rectangular bars — Tolerances on shape and dimensions ISO 6362-4. Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 4: Profiles — Tolerances on shape and dimensions ISO 6362-5. Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and…

ISO 6362-2-2014 pdf free.Wrought aluminium and aluminium alloys – Extruded rods/bars, tubes and profiles一 Part 2: Mechanical properties. This part of Iso 6362 specifies the mechanical properties of wrought aluminium and aluminium alloy extruded rods/bars, tubes, and profiles for general engineering applications. It applies to extruded products. 2 Normative references The following documents, in whole or In part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6362-i. Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 1: Technical conditions for Inspection and delivery 150 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature ASTM B557M, Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium- Alloy Products 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6362-1 apply. 4 Tensile testing For the selection of the specimens and tensile testing, see ISO 6892-1 or ASTM BSS7M. 5 Mechanical properties Values for mechanical properties of aluminium and aluminium alloys are given in Tables ito…

ISO 6361-3-2014 pdf free.Wrought aluminium and aluminium alloys一Sheets, strips and plates一 Part 3: Strips: Tolerances on shape and dimensions. This part of Iso 6361 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy strip by cold-rolling for general engineering applications. It applies to products with thickness of over 0.15 mm up to, and including 16 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further roiling (reroll stock), or to special products such as those that are corrugated or embossed. Technical conditions for inspection and delivery of products covered by this part of ISO 6361 are specified in ISO 6361-1. 2 Dimensional tolerances 2.1 Thickness Thickness tolerances shall be in accordance with Tables 1 and 2.. When the tolerance is specified as either all plus, or minus side, the value in Table 1. or in Table 2. shall be doubled. Tolerances for the products exceeding the range of specified thickness and width shall he agreed upon by the purchaser and the supplier. 2.2 Width Width tolerances shall be in accordance with Table 3. When the tolerance is specified as either all plus, or minus side, the value in Table…