ISO GUIDE 30-2015 pdf free.Reference materials – Selected terms and definitions.
This Guide recommends terms and definitions that should be used in connection with reference materials, with a particular emphasis on terms that are used in reference material product information sheets, certificates and corresponding certification reports.
2 Terms and definitions
2.1 Terms related to materials
2.1.1 reference material RM material, sufficiently homogeneous and stable with respect to one or more specified properties, which has been established to be fit for its intended use in a measurement process
Note I to entry: RM is a generic term.
Note 2 to entry: Properties can be quantitative or qualitative. e.g. identity of substances or species.
Note 3 to entry: Uses may include the calibration of a measurement system, assessment of a measurement procedure, assigning values to other materials, and quality control.
Note 4 to entry: ISO/I EC Guide 99:2007111 has an analogous definition (5.13), but restricts the term “measurement” to apply to quantitative values. However, Note 3 of ISO/IEC Guide 99:2007, 5.13 (VIM), specifically includes qualitative properties, called nominal properties”.
2.1.2 certified reference material CRM reference material (RM) characterized by a metrologically valid procedure for one or more specified properties, accompanied by an RM certificate that provides the value of the specified property, its associated uncertainty, and a statement of metrological traceability
Note 1 to entry: The concept of value includes a nominal property or a qualitative attribute such as identity or sequence. Uncertainties for such attributes may be expressed as probabilities or levels of confidence
Note 2 to entry: Metrologically valid procedures for the production and certification of FtMs are given in, among others, ISO Guides 34121 and 35131.
Note 3 to entry: ISO Guide 31141 gives guidance on the contents of RM certificates. Note 4 to entry: ISO/IEC Guide 99:2007111 has an analogous definition (5.14).
2,1.3 candidate reference material material, intended to be produced as a reference material (RM)
Note 1 to entry: A candidate material has yet to be characterized and tested to ensure that it is fit for use in a measurement process. To become an RM, a candidate material needs to be investigated to determine if It is sufficiently homogeneous and stable with respect to one or more specified properties, and is fit for its intended use in the development of measurement and test methods that target those properties.
2.14 matrix reference material reference material that is characteristic of a real sample EXAMPLE Soil, drinking water, metal alloys, blood.
Note 1 to entry: Matrix reference materials may be obtained directly From biological, environmental or industrial sources.
Note 2 to entry: Matrix reference materials may also be prepared by spiking the component(s) of interest into an existing material.
Note 3 to entry: A chemical substance dissolved in a pure solvent is not a matrix material.
Note 4 to entry: Matrix materials are intended to be used in conjunction with the analysis of real samples of the
same or a similar matrix.
2.1.5 primary measurement standard measurement standard that is designated or widely acknowledged as having the highest metrological qualities and whose property value is accepted without reference to other standards of the same property or quantity, within a specified context
Note I to entry: See also ISO/IEC Guide 99:2007,111
2.1.6 secondary measurement standard measurement standard whose property value is assigned by comparison with a primary measurement standard of the same property or quantity
Note Ito entry: See also ISO/IEC Guide 99:2007,111
2.1.7 sample portion (amount) of material taken from a batch.ISO GUIDE 30 pdf download.
Tags: Reference materials
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…