ISO 17842-1-2015 pdf free.Safety of amusement rides and amusement devices – Part 1: Design and manufacture.
This part of Iso 17842 specifies the minimum requirements necessary to ensure the safe design, calculation, manufacture, and installation of the following: mobile, temporary or permanently installed machinery and structures, e.g. roundabouts, swings, boats, Ferris wheels, roller coasters, chutes, grandstands, membrane or textile structures, booths, stages, side shows, and structures for artistic aerial displays. The above items, hereafter called amusement devices or simply devices”, are intended to be installed both repeatedly without degradation or loss of integrity, and temporarily or permanently in fairgrounds and amusement parks or any other locations. Fixed grandstands, construction site installations, scaffolding, removable agricultural structures and simple coin operated children’s amusement devices intended for up to 3 children are not covered by this document.
Nevertheless this document can be used in the design of any similar structural or passenger-carrying device not explicitly mentioned herein.
Existing national rules on workers’ safety are not concerned by this document.
This document is applicable to amusement devices and major modifications of amusement devices and rides manufactured after the effective date of its publication.
ISO 17842-3 contains requirements for inspection during design, manufacture, operation and use.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 288-9, Specification and approval of welding procedures for metallic materials — Part 9: Welding procedure test for pipeline welding on land and offshore site butt welding of transmission pipelines
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolt.c, screws and studs with specified property classes — Coarse thread and fine pitch thread
ISO 1141, Fibre ropes — Polyester — 3-, 4-, 8- and 12-strand ropes
ISO 1181, Fibre ropes — Manila and sisal — 3-, 4- and 8-strand ropes
ISO 1346, Fibre ropes — Polypropylene split film, monofilament and multifilament (PP2) and polypropylene high-tenacity multifilament (PP3) — 3-, 4-, 8- and 12-strand ropes
ISO 2307, Fibre ropes — Determination of certain physical and mechanical properties
ISO 3834-1, Quality requirements for fusion welding of metallic materials — Part 1: Criteria for the selection of the appropriate level of quality requirements
ISO 3834-3, Quality requirementsforfusion welding ofmetallic materials— Part3:Standard quality requirements ISO 4014, Hexagon head bolts — Product grades A and B
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 17842-2, ISO 17842-3, ISO/IEC 17020 and ISO/TS 17929, and the following apply.
NOTE Any symbols connected with the respective terms or units are explained in the clauses concerned.
3.1 amusement device
arrangement of equipment that produces the desired effect of amusement or entertainment when the patron (3.25) moves through it or on it primarily by his or her own action, or any other system that is not covered by the term amusement ride (3.2)
Note 1 to entry: In this document, the word “device” is used to refer to an amusement device or amusement ride (3.2).
3.2 amusement ride equipment that is designed to entertain the passengers (3.25) during motion including biomechanical efectst
Note 1 to entry: In this document, the word “device” is used to refer to an amusement device (3.1) or amusement ride.
Note 2 to entry: See ISO/TS 17929 for the definition of biomechanical effect.ISO 17842-1 pdf free download.
Tags: Safety of amusement rides
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…