ISO 13680-2020 pdf free.Petroleum and natural gas industries – Corrosion-resistant alloy seamless tubular products for use as casing, tubing, coupling stock and accessory material一Technical delivery conditions.
This document specifies the technical delivery conditions for corrosion-resistant alloy seamless tubular products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels:
— PSL-1, which is the basis of this document;
— PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the Iso 15156 series.
At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1.
NOTE I The corrosion-resistant alloys included in this document are special alloys in accordance with ISO 4948-1 and ISO 4948-2.
NOTE 2 For the purpose of this document, NACE MR0175 is equivalent to the ISO 15156 series.
NOTE 3 Accessory products can be manufactured from coupling stock and tubular material, or from solid bar stock or from bored and heat heat-treated bar stock as covered in Annex F.
This document contains no provisions relating to the connection of individual lengths of pipe. This document contains provisions relating to marking of tubing and casing after threading. This document is applicable to the following five groups of products:
a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure;
b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy;
c) group 3, which is composed of stainless alloys with an austenitic structure (iron base);
d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base);
e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure.
NOTE 4 Not all PSL-1 categories and grades can be made cracking resistant in accordance with the ISO 15156 series and are, therefore, not included in PSL-2.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (incluiding any amendments) applies.
ISO 377, Steel and steel products一Location and preparation of samples and test pieces for mechanical testing
Iso 404, Steel and steel products一General technical delivery requirements
ISo 525, Bonded abrasive products一General requirements
Is0 643, Steels- Micrographic determination of the apparent grain size
Iso 3452-1, Non-destructive testing一Penetrant testing一Part 1: General principles
ISo 4287, Geometrical Product Specifications (GPS)一Surface texture: Profile method一Terms, definitions and surface texture parameters
ISo 4885, Ferrous materials – – Heat treatments一Vocabulary
Is0 4948-1, Steels一Cassification 一Part 1: Cassification of steels into unalloyed and alloy steels based on chemical composition
IS0 4948-2, Steels – Cassification 一Part 2: Cassification of unllyed and lly sees according to main quality classes and main property or application characteristics
ISO 6508-1, Metallic materials一Rockwell hardness test一Part 1: Test method
ISo 6508-2, Metallic materials一Rockwell hardness test一Part 2: Verification and calibration of testing machines and indenters
IS0 6892-1, Metallic materials一Tensile testing一Part 1: Method of test at room temperature
ISo 6892-2, Mtallic materials一Tensile testing一Part 2: Method of test at elevated temperature
Iso 6929, Steel products一Vocabulary
ISO 8501-1, Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness一Part 1: Rust grades and preparation grades o uncoated steel substrates and of steel substrates after overall removal of previous coatings
IS0 9712, Non -destructive testing一Qualification and certification of NDT personnel
1S0 9934-1, Non-destructive testing一Magnetic particle testing一Part 1: General principles
ISO 10423, Petroleum and natural gas industries一Drilling and production equipment一Wellhead and christmas tree equipment.ISO 13680 pdf download.
Tags: Petroleum and natural gas industries
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…