ISO 11971-2020 pdf free.Steel and iron castings 一 Visual testing of surface quality.
1.1 This document covers the acceptance criteria for the visual testing of the surface of steel and iron castings.
1.2 Acceptance levels utilize Bureau de Normalisation des Industries de Ia Fonderie (BNIF] and Steel Castings Research and Trade Association (SCRATA) or Casting Technology International ICTIJ reference comparators for the visual determination of surface roughness and surface discontinuities described as follows:
surface roughness:
thermal dressing:
mechanical dressing:
non-metallic inclusions:
gas porosity;
fusion discontinuities;
expansion discontinuities;
metal inserts.
2 Normative References
There are no normative references in this document.
3 Terms and Deflnitions
No terms and definitions are listed in this document.
ISO and IEC maintain tertninological databases for use in standardization at the following addresses:
ISO Online browsing platform: available at https://www.iso.org’obp
IEC Electropedia: available at http://ww w .elecopedia.org/ 4 Ordering information
The enquiry and order should specify the following information:
a) the casting areas where the surface is to be tested should be clearly indicated on the drawing or solid model:
h) the number of castings to he tested;
C) the acceptance level: more than one acceptance level may he specified for different surfaces of the same casting;
d) if any types of discontinuities are unacceptable.
5 Test method
The area to be tested shall be examined without optical aids exceeding lx magnification.
The comparators define the worst or roughest condition tbr that acceptance level. 6 Acceptance criteria
a The SCRATA comparator set is used for steel or iron castings.
b) The BNIF comparator set SI and S2 categories can be used for all alloys. Category S3 is used for steel castings only.
Table I lists BNIF and SCRATA comparators for surface roughness and gives the equivalency between BNIF and SCRATA comparators for surface roughness, mechanical dressing and thermal dressing.
Table 2 lists the SCRATA surface-discontinuity comparators.
Levels of acceptance for surface roughness and discontinuities may he specified by the customer. In Annex A. Table A.l and Table A.2 give guidance on optional roughness acceptance and surface discontinuity acceptance.
Surface discontinuities not covered by this document shall he a matter of agreement between the purchaser and manufacturer.ISO 11971 pdf free download.
Tags: Steel and iron castings
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…