BS ISO 10571:2016 pdf free.Tyres for mobile cranes and similar specialized machines.
BS ISO 10571 specifies the designation, dimensions, load ratings and reference speed for tyres and rims fitted to vehicles, such as all-terrain equipment, mobile cranes, crash tenders, etc., likely to operate on highway over long distances at reference speed and under constant load.
2 NormatIve references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 4209— 1:2001, Truck and bus tyres and rims (metric series) — Part 1: Tyres
ISO 4223-1, Definitions of some terms used in the tyre industry — Part 1: Pneumatic tyres
ISO 4250—3, Earth-mover tyres and rims — Part 3: Rims
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4223-1 apply.
NOTE Equivalent terms are given in ISO 3877-1.
4 Tyre designation and marking
The designation of the tyre shall be shown on its sidewall and shall include the details in 4j. Additional markings as shown in 4. 4 and 4,.4 may also be included as required by regional regulations or practices.
5 Tyre dimensions
Table 3 and Table 4 show the following, for 95 series and 80 series tyres, respectively:
a) tyre designation as indicated in ClauseA
b) measuring rim width code;
c) design tyre dimensions, i.e. section width and overall diameter;
d) maximum tyre dimensions in-service.
6 Tyre load capacities
6.1 Basic lyre loads
Basic tyre load ratings at 70 km/h (speed symbol E) reference speed are given in Table 5 and Table 6 for 95 series and 80 series tyres, respectively, and at 80 km/h (speed symbol F) reference speed, in Table 7 and Table 8. for the 95 series and 80 series tyres, respectively.
6.2 Limitations
In some countries, there can be load/speed/inflation pressure limitations because of national requirements.
6.3 Tyre loads at speeds other than reference speed
When a tyre is fitted on a vehicle with a maximum speed capability different from the tyre reference speed, load capacities shall be modified as shown in Table 9 and Table 10.
6.4 Tyre selection
Speed symbol E tyres are used primarily for cranes with low speed capability (rough terrain applications). Cranes with higher speed capability (all-terrain applications) can require a speed symbol F tyre. Speed symbol E and speed symbol F tyres are not interchangeable on a given application because of the difference in their load carrying capability at the same speed (refer to Table 5. Table 6. Table 7 and Table 8).BS ISO 10571 pdf free download.
Tags: Tyres for mobile cranes and similar specialized machines
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…