BS ISO/IEC 8484:2014 pdf free.Information technology – Magnetic stripes on savingsbooks.
BS ISO/IEC 8484 specifies the characteristics and location of a magnetic stripe on a savingsbook as defined in Clause .4 and the use of such savingsbooks for international interchange. Compatibility with international interchange systems is provided through the requirements of this International Standard, enabling a savingsbook with a magnetic stripe to be read and possibly encoded in a device that is compatible with reading identification cards used in international interchange.
This International Standard specifies requirements for a magnetic stripe (including any protective overlay) on a savingsbook, the encoding technique, and coded character sets. It also specifies the characteristics of the savingsbook cover such as stiffness, minimum size, surface irregularities, roughness, and interaction between the cover material and the magnetic stripe. It takes into consideration both human and machine aspects and states minimum requirements.
Coercivity influences many of the quantities specified in this International Standard but is not itself specified. Exposure of the savingsbook to a magnetic field is likely to destroy the recorded data.
This International Standard defines performance criteria for savingsbooks. No consideration is given within this International Standard to the amount of use, if any, experienced by the savingsbook prior to test. Failure to conform to specified criteria will be negotiated between the involved parties.
ISO/IEC 10373-2 specifies the test procedures used to check savingsbooks against the parameters specified in this International Standard. References in the test method to cards refer to savingsbooks,
NOTE 1 Numeric values in the SI and/or Imperial measurement system in this International Standard might have been rounded off and are therefore consistent with, but not exactly equal to, each other. Either system can be used, but the two are not be intermixed or reconverted. The original design was made using the Imperial measurement system.
NOTE 2 National systems can use different specifications, such as DIN, as well as proprietary specifications for closed systems.
2 Conformance
A savingsbook is in conformance with this International Standard if it meets all mandatory requirements specified herein. Default values apply if no others are specified.
3 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 2493, Paper and board — Determination of resistance to bending
ISO 4287, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters.BS ISO/IEC 8484 pdf download.
Tags: Information technology
-
ISO 8600-1-2013 pdf free download.Endoscopes – Medical endoscopes and endotherapy devices – Part 1: General requirements. 6 Marking 6.1 Minimum marking Iach individual endoscope or endotherapy device shall have the lollowing minimum marking: a) model number and/or other mark sufficient to identify the endoscope or endotherapy device and its manufacturer; b) maximum insertion portion width, minimum instrument channel width, working length, field of view and/or direction of view where such identification is necessary for the intended use of the endoscope or endotherapy device. The Insertion portion width and instrument channel width units shall be in millimetres. The insertion portion width and instrument channel width can also be marked in French size as defined in 3.5, shown by either ‘Fr or an encircled number; c) wherever reasonable and practicable. the endoscope or endotherapy device and detachable component(s) shall be identified in terms of lot numbers or serial numbers, etc. 6.2 Marking legibility The marking shall remain legible over the lifetime of the device when the endoscope or endotherapy device is used, cleaned, disinlected, sterilized and stored in accordance with the instruction manual. 6.3 Marking exceptions When marking on the endoscope or endotherapy device or detachable component(s) is impossible to achieve due…
-
ISO 15688-2012 pdf free download.Road construction and maintenance equipment – Soil stabilizers 一 Terminology and commercial specifications. This International Standard establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. It does not apply to soil stabilizers used in agricultural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.. ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking ISO 6746-1, Earth-moving machinery — Definitions of dimensions and codes — Part 1: Base machine ISO 6746-2, Earth-moving machinery — Definitions of dimensions and codes — Part 2: Equipment and attachments ISO 7134. Earth-moving machinery — Graders — Terminology and commercial specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 soil stabilizer self-propelled machine, either towed or transported, with the function of pulverizing, breaking-up, aerating, homogenizing, and loosening existing and imported soil or paving materials and mixing them…
-
ISO 18436-1-2012 pdf free.Condition monitoring and diagnostics of machines – Requirements for qualification and assessment of personnel一 Part 1: Requirements for assessment bodies and the assessment process. 5 Requirements for assessment body personnel 5.1 General provisions In order to ensure that the assessment process is carried out effectively and uniformly, the competence requirements for personnel involved in the entire process shall be defined by the assessment body and, in the case of a third party, be approved by the responsible TCC (in accordance with ISO/IEC 17024). The assessment body shall require its personnel (internal or external) to sign a contract, or other document, by which they commit themselves to comply with the rules defined by the assessment body, including those relating to confidentiality and those relating to independence from commercial and other interests, and from any prior or present link with the persons to be examined that would, in the opinion of the interested parties, compromise impartiality. Clearly documented instructions shall be available to the personnel, describing their duties and responsibilities. These instructions shall be maintained up to date. All personnel involved in any aspect of assessment activities shall possess appropriate educational qualifications, experience and technical expertise, which satisfy defined…